Detailed introduction of Glass Shower Enclosure MBL-6701
Size:90*90*205cm 6mm tempered safety glass,aluminum alloy,ABS tray
Specification of Glass Shower Enclosure MBL-6701
A) Material:ABS composite board with 100% resin and three layers fibreglass reinforced under shower tray,tempered safety glass,stainless steel
6mm tempered safety glass, satin silver aluminium alloy profile
C) Optional function:
shining silver aluminium alloy profile,white aluminium alloy profile
Inner packing:Styrofoam.Outer packing:Carton box.
Various manners of packing is available upon request
0.25 CBM, Catron box:4 pcs
0.27 CBM, Catron box:4 pcs
0.29 CBM, Catron box:4 pcs
OEM service and mixed models is available
We can modify our products according to your requirements
- Q:Shower room of the thickness of the retaining bar to be appropriate ah?
- Shower room retaining bar is generally 40MM to 50MM high, thick is almost 30MM to 40MM. Are generally finished stone processing. Not expensive, generally in the 150 / mil. A shower room to block the water on the 1 meter wide. It is almost 200 dollars. You can go to Kai Li asked, their home shower room water effect done quite fine.
- Q:Shower room, glass interlayer and surface coating, which is more secure?
- Surface coating of the security of the film.
Today, most of the shower room is made of tempered glass, belonging to the national safety glass range. However, there is also the possibility of broken glass, the following comparison between the tempered glass and laminated glass What is the difference.
Tempered glass impact resistance: Toughened glass high strength, the compressive strength of up to 125MPa or more, in normal people under normal collision will not rupture but fear of normal collision of conical hard objects, such as the bus installed on the cone Small hammer, the use of only a relatively small force can be tempered glass broken. Crushing particle size: steel safety glass after the particle size was 6mmX6mm size of the granular. Almost the whole piece of glass fragments will be scattered on the ground, the human body or third party objects may cause minor damage.
Laminated glass advantages of the definition: laminated glass, is between the two pieces of glass into a layer of polyvinyl butyral as the main component of the PVB interlayer. Even if the glass fragmentation, debris will be sticky on the film on the broken glass surface remains clean and smooth. Impact resistance: sandwich safety glass impact strength than the tempered glass and then more than 5 times stronger, to drop the ball impact test method, the laminated glass flat on the ground, with a maximum of 2.26kg of steel The ball falls from a height of up to 2.8 m, and the glass remains intact (6 pieces of experimental glass allow only one piece to break).
- Q:What is the main choice of the shower room?
- As a user of Furui, I strongly do not recommend Furui.
Mainly believe that one of the top ten brands of misleading, bought last year, Furui. But with a 3 months (accurate terms, less than 1 month, because this period in the new house to stay time is not much), there are many hardware rust.
The phone to inform me to buy the shower room sales, always arranged for different people to contact me after-sales processing, each time to send photos, photos made in the past, on the rocks of the sea.
3 months have passed, or no one to deal with.
In this 3 months time, no one has always been active contact me, whether aftermarket, or sales. I have played a lot of calls.
I ask is not high, there are problems to deal with ah? There is no attitude to deal with, there is no intention to deal with, this is to do business to do the rhythm of death ah!
- Q:What is the shower room industry?
- Home bathroom
- Q:Shower room glass glue mold point how to remove?
- You can use a hot cloth to wash away the detergent, and then use alcohol disinfection.
To remove many of the methods, you can try the following:
1, with soap plus a little ammonia and turpentine mixture, you can remove many dirt
2, with a good sticky transparent glue repeatedly tear, you can remove some of the surface
3, with a little bit of sodium water to wipe off, or paint thinner can also be.
4, you can use hair dryer dry, and then gently scraping on it
5, wipe with a cotton swab dipped in water.
6, wind oil fine wipe.
7, use a special cleaning agent or sports shoes to remove the cream wipe.
8, with the drawing with the 4b rubber is very soft that kind of Korean rubber can erase it.
9, if it is a long trace of traces have been hardened, you can use a hot towel to get it soft and then rub.
- Q:Shower room how to clean the glass
- 1. Scrapping tool to remove the glass water, watering cans, scouring pad, glass scraping edge with a watering cans to add glass water at any time. Where the scouring pad can be replaced by a better absorbent sponge effect better. Because the removal of scale in fact does not require too much friction, as long as the glass water is full, easy to dissolve scale. Take a look at the effect of wiping, the left is not rubbed, the right is rubbed. Wipe clean, every time the bath, as long as the cold water from top to bottom again, and then scratch the glass clean, you can always keep clean as new, cold water red purpose is to avoid the individual has been dry small water droplets The If it is a new shower room, then even the glass of water are not on, as long as the shower after the cold water again and then scratch the glass again can be used frequently new. 2. I can also try a way to remove the stain on the glass of the shower room that is the skin of the potato. Potato skin inside the rich is rich in starch so as long as the potato skin to wipe the glass, the glass will be because of the dust to the stains away the reason, leaving the original fog shower room glass, still still bright as new, flashing Yo. 3. paper towels dipped in vinegar with a paper towel to repair the master also told me that the best thing to clean the glass is napkins, paper towels dipped in vinegar with a paper towel wiped it. 4. Jeans wipe the water stains Do not cut the appropriate size of the jeans plus water, in a place where the water back and forth to wipe a few times, shower room glass water stains naturally gone, where the rub did not leave traces Oh.
- Q:Which brand of shower is better?
- Good brand has a lot, do not know what you need to position, and now the comparison of Guangdong China, the price is also expensive, a sub-price goods, I do shower room, days Mu, the price can also (And China other brands) quality no problem.
- Q:What is the installation of the shower room? How is the glass fixed?
- You can use embedded, that is, before setting the shower room on the ground to put the marble back buried. This way is too much trouble, not easy to replace.
You can also use glass adhesive paste, will buy back the retaining stone with glass glue and ground connection. This way no damage to the floor, easy to replace.
Glass and ground water stone, if it is flat open the door will generally have the code, which requires drilling on the marble, there is a marble in the already opened a groove, this will be directly into the glass glass Glue can be.
- Q:Home shower room glass how to choose
- Now say that their glass is what Yaohua, CSG, but the vast majority are Huyou you, the real use of these two original film prices will not differ too much, because these two expensive, and domestic Shower room most manufacturers will not use (export may be more foreign), really in the domestic market with CSG, Yaohua's very little, I suggest you can call him to prove it
- Q:Bathroom shower room on the glass sliding door is how the assembly, which experienced guidance, thank you
- Toilet shower room on the sliding door of the glass installation, the wheels should be installed on the door, and then the wheel to the lowest position, and then put the door on the card slot, and finally the wheel to the appropriate position.
Sliding door is the door that connects the pulley and is movable on a fixed track, also known as a sliding door. It is different from the hinge to connect the door to open the door. The sliding door is easy to install, can be reused, can be industrialized production, can also be small workshop production, fire, environmental protection and so on.
We specialize in the development and production of computerized steam rooms, shower rooms, shower enclosures, shower panels,shower cabins,bathtubs,massage bathtubs,whirlpool bathtubs, bathroom vanities, bathroom cabinets,tempered glass basins etc.
We believe that quality is an integral part of manufacturing process, and our laboratory is fully fitted with modern testing equipment to carry out all tests needed.
Due to our high quality products and favorable prices, our products sell well around China and are exported to nearly twenty foreign countries, such as Canada, Germany, Mexico, Poland, Russia, Kazakhstan, Syria, Turkmenistan, United Arab Emirates, Vietnam, Egypt, Kenya and so on.And We will continue to offer OEM service all the time.
1. Manufacturer Overview
|Annual Output Value
||US$2.5 Million - US$5 Million
||North America; South America; Eastern Europe; Southeast Asia; Africa; Oceania; Mid East; Eastern Asia; Western Europe
||CERTIFICATE OF CONFORMITY (ISO9001); CERTIFICATE OF CONFORMITY (CE)
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||3,000-5,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range