Chemical Mixed-flow Pump

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT or LC
Min Order Qty:
1 unit
Supply Capability:
1000 Sets Per Month unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

High pump efficiency, low energy consumption Pump can evenly consume energy within all performances. Pump can be started when the valve is closed, and the motor does not overload.
Large flow proportion and uneasily blocked.
Solidity structure and long life.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:The carbon pump is blocked, the Walla fell, the total amount of money to clean the engine?
The carbon pump is blocked, the Walla fell, the total amount of money to clean the engine?
Q:What about the oil leakage of automobile oil pump?
If the oil pump is broken, replace it, if it is a rubber pad, change the cushion
Q:Automobile engine oil pump does not leak pressure, which causes oil seal ring to leak seriously. What is the trouble?
1, check whether there is lack of oil.2, the condition is not very old, check the oil pressure sensor.3, sensor no problem, check the oil pump, see if the pump is not enough oil.Automobile engine oil pump with crank, when the engine speed of pump oil is high, therefore need a pressure relief valve to keep the oil pressure of the main oil channel, the excess oil drain back to the oil pan, if the oil pump pressure relief valve failure, no pressure relief will lead to the oil pressure is too high, will be oil lattice sealing collopse. If the pressure relief valve normally open, it will cause oil pressure is too low, will burn bearings and the like.
Q:Does the abnormal oil pump affect power?
Hello, oil pump damage will result in lower oil pressure, engine noise, and accelerate the wear and tear of the car to start the internal parts
Q:The car leaked oil and replaced an oil pump
First of all, it is necessary to make sure that the oil is dripping from there and how many drops can be made at one night. These can be checked out by themselves. The problem of one or two drops at one night is too small. Because change pump that has removed the cylinder, the cylinder and the pump is mat, the mat will not handle drop of oil, and the oil filter is opened, if not installed it will leak if these local oil spills, they will help you to reload.
Q:How does the motor pump exhaust the air?
The oil pump doesn't need to exhaust air
Q:How to repair the Iveco oil pump
The oil pump can not be repaired by itself, nor can the repair factory repair it
Q:The car burning oil pump replacement must do
1, there are many reasons, but also models (steam, firewood) and so on.2, long-term use of poor quality oil, or viscosity grade unqualified engine oil and other internal wear too large.3, under normal circumstances, the engine will burn some of the oil from the cylinder block, piston and valve lubrication, consumption within the relevant provisions of the national standard range for normal (GB/T19055), and vice versa. The lowest scale car burning oil is often accompanied by smoke or in a maintenance period is lower than the oil gauge oil level.4, long time does not change oil or too long delay, not timely maintenance; piston and piston ring due to the use of long, normal wear, or abnormal wear and tear caused by the gap is too large.5, in addition, there are valve seals, crankcase forced ventilation, PCV valve damage, congestion, oil pump pressure, or its own failure can also be caused.There are many reasons why, as you describe the content is not detailed, the temporary analysis so far.
Q:The chain pump 2.4 of the modern business did not mark how to install?
This car pump is no point in time, you can install
Q:How do you install the pedal motor pump?
Put the unit on the foundation with anchor bolts, between the base and the base, and use a pair of wedge pads.Release the axle shaft and place on the pump shaft and base with a level gauge. Adjust the level of the machine by adjusting the wedge pad and tighten the anchor bolts properly so as not to move around.Correct the concentricity of the pump shaft and the motor shaft, and allow the deviation of 0.1 mm on the outer circle of the axle shaft; two the clearance of the coupling plane shall be guaranteed 2~4 mm, and the clearance shall be uniform, and the tolerance shall be 0.3 millimeters.After connecting the pipeline and determining the direction of the motor rotation, then coupled with the coupling, and then check the concentricity of the shaft.In the actual test run 2~3 hours after the unit, for final inspection, if there is no adverse phenomenon, that the installation of qualified. Check the temperature and vibration of the bearing during the test run.During installation, all holes in the unit shall be covered to prevent debris from falling into the machine.In order to prevent the sundries from entering the pump, the filter shall be installed on the newly installed pipeline. The effective cross section shall be 2-3 times larger than the cross section of the suction pipe.However, the oil pump rarely fails, generally as long as the opening of the cylinder head, see more fresh oil or start the engine, there is oil jet, indicating the normal operation of the oil pump.
Our main products are all kinds of centrifugal pumps, displacement pumps and vacuum pumps, such as oil pumps, multi-phase pumps, single stage and double suction centrifugal pumps, horizontal split case pumps, multistage pumps, axial-flow pumps, mixed flow pumps, petrochemical pump and submersible pumps. Besides, our company also manufactures electric motors and sells electric motors, building materials, indoor decoration materials, civil electric equipment, devices and instrumentation, as well as exports our mechanical and electric products.

1. Manufacturer Overview

Location Hunan,China
Year Established 2006
Annual Output Value US$5 Million - US$10 Million
Main Markets 59.00% Mid East
8.00% North America
8.00% Southern Europe
5.00% Eastern Asia
2.00% Africa
2.00% Oceania
2.00% Southeast Asia
2.00% Western Europe
2.00% South America
2.00% Central America
2.00% Northern Europe
2.00% Eastern Europe
2.00% South Asia
2.00% Domestic Market
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port SHANGHAI,GUANGZHOU,DALIAN
Export Percentage 51% - 60%
No.of Employees in Trade Department 6-10 People
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: Above 100,000 square meters
No. of Production Lines Above 10
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range High and/or Average