Q:What's the best way to use the cooling tube in CSO's deadly trap?

The middle of the screen will prompt ~ ~ go to the lighted tube ~ walk to the side and press the E button

Q:Rifled or smoothbore gun is? Why does it only use water cooling pipes, while anti-aircraft guns, infantry fighting vehicles and artillery guns do not? Thanks a lot!

Naval gun is line bore.A pre war artillery is smoothbore, modern MBT high-pressure tank gun unrifled.To solve the problem of heat dissipation, the gun must use water, because the gun caliber is relatively large, the largest caliber gun projectile was 406mm, weighing 1 tons, the charge is great, big guns such as long as the launch of a projectile gun will be red, without water, can not play the 10 shell guns will be ruined.Such as artillery, artillery and other small caliber, little charge, the launch of the heat is not enough, air cooling will be enough.It's like the car has to be water-cooled and the motorcycle doesn't need it. The air cooling of the motorcycle is enough. There is no need to add water.

Q:What is the cause of the resonance in the cooling pipe of the central air conditioner?

General central air conditioning with electromagnetic expansion valve, depending on the sound, where the resonance, and see if the throttle valve is sound. If the effect is very good, you can consider the fixed vibration parts, and if the effect is not good, we should consider whether the pipeline appears to throttle, bend the place is whether the copper tube deflated. This problem is troublesome.

Q:What is the cooling water pipe of an automobile engine?Who can explain the introduction of the cooling water pipe of the automobile engine?

The cooling water pipe for automobile engine assembly in the presence of interference fit in the assembly process, if the amount of interference is too large, it is difficult to assemble, and easy to cause large deformation; if the amount of interference is too small, water and easy to fall off and Water Leakage. Carries on the simulation analysis using the finite element method, the assembly of different interference under the effect of size changes and pipe assembly force required and the amount of interference on the automobile engine cooling water pipe assembly to improve the best fit.

Q:Is the water switch for the central air conditioner installed on the cooling water pipe or the cooling water pipe?

The water switch is used to protect the central air conditioner from running out of water, so cool and freeze all two pipes and install it on the outlet pipe

Q:The engine cooling pipe is stiff and can not pinch

The car is old. That's normal

Q:My car is a 125CC assembly off-road vehicle. The engine is Tanaka's. Can this engine load the oil cooler?By the way, what is the lubrication of this engine?

Oil cooling is to achieve better lubrication effect but I see in the picture that stuff you said fitted to the exhaust pipe of the exhaust pipe temperature reaches what such a hundred degrees is not baked lubricating oil will be more hot! The lubrication of the engine is to press the oil pump into the oil passage and deliver it to the parts that need lubrication through the oil passage

Q:In what circumstances should mass concrete be buried with cooling pipes?

Hydration heat is too large, external facilities can not guarantee the temperature difference between the internal and external, must be set.

Q:How to scale the cooling water pipe of vacuum pump reducer?

The possible reason is that deep water calcium ion concentration is high, using vacuum pump seal water device of adding acid, but there is no obvious effect, and the internal corrosion of pump body, finally decided to try desulfurization process water as a vacuum pump seal water supplement, cancel the device of adding acid. Vacuum pump fouling is a very common phenomenon, it is best to think of some ways of running, such as regular switching, regular cleaning.

Q:What is the biggest difference between a plastic cooling pipe and a serpentine pipe, like a serpentine one? Are they all used on machine tools?

Snake shaped universal joint metal cooling pipe: it is a kind of product used by various machine tools, mechanical equipment and so on, which is used to process workpieces, over oil, over water or gas for cooling and cooling. Main body is made of spring 65 manganese spring steel, surface chrome plated, stainless steel gloss not rust and oxidation, is lined with white plastic hose and a sealing plastic tube, arbitrary bending, long service life.The metal cooling pipe has internal and external threads and can be divided into English and metric threads. English thread commonly used to have 3/4,1/2, 3/8, 1/4,1/8 and other models, metric thread commonly used to have m20*1.5, m18*1.5, m16*1.5, m14*1.5 and other models. Length can be made by actual use as long as 100mm to 2000mm. At the same time, the water cooling end of the metal cooling pipe can be made into a rotary switch with controlled water output and a single nozzle or a flat nozzle.Plastic cooling pipe: suitable for machine tools, hydraulic machinery, CNC machine tools for the oil and water cooling system used, the product is assembled by hand, can arbitrarily adjust the use length, nozzle diameter round flat direction can be freely interchangeable, and has the characteristics of beautiful color appearance, large amount of oil, not conductive, corrosion resistance and high temperature etc..Plastic cooling pipe D1d1d2D2LL31-5G1/4 "1.534.51825 14280L31-5G3/8 6.5324021410" L31-5G1/2 "6.5105024410 Description: G1/4" 13mm G3/8 "each length of each length 17.5mm G1/2 21mm note: each length length according to the needs of the user defined.