Rubber Foam Heat Insulation Tube
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 20 Cubic Meters m³
- Supply Capability:
- 200000 Cubic Meters per Year m³/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Detailed Product Description
1.air conditioning ,industrial cooling etc pipe;
2.low conductivity factor;
3.Self extinguishing,
4.air conditioner duct tube
1.Product features:
It is an elastomeric rubber based insulation material in the form of sheet and pipe with closed cell structure which doesn’t contain CFC halogen materials (chlorine, bromine, etc.) and PVC. It is manufactured to be used for air conditioning, heating and cooling systems.It has high thermal insulation value. It can be faced with aluminium foil and can be self-adhesive.
2. Application:
It is a black coloured elastomeric rubber based insulation material in the form of sheet and pipe with closed cell structure It is used on the exterior surfaces of the ducts and large diameter pipe lines in the heating, cooling and air conditioning systems for thermal insulation and condensation control purposes. It is developed to use at battleships, merchant ships, transportation systems; in areas where there are crowds of people such as business and entertainment places, hospitals, airports in order to reduce the emissions of smoke and poisonous gases. The sheets are adhered to the duct surface by using a special adhesive that it suggested. For the pipe applications, the pipe to be insulated and the rubber surface should fit properly and no gap should be left in between. Joints should be tightly sealed and they should be covered with insulation tape afterwards if necessary. Taping should not result in thickness loss. The application should be protected against distruption and rupture.
- Q:What's the best way to use the cooling tube in CSO's deadly trap?
- See white, and then go, press E
- Q:Can you tell me how to distinguish the freezing pipes, cooling pipes and condensate pipes in HVAC engineering?
- The chilled water is supplied at the end of the fan coil and the temperature is 7-18 degrees. The exterior is usually insulated with rubber and plastic;The cooling water is supplied to the refrigerator and is used without heat. The exterior is painted with green industrial paint;The condensed water pipe is generally installed at the lower part of the fan coil, and is connected with the water receiving plate, and introduces a floor drain or a collecting device without cold protection and brushing.
- Q:The engine cooling pipe is stiff and can not pinch
- The car is old. That's normal
- Q:Volkswagen Sagitar cooling pipe, three pass joint, what is the name of
- Water pipe three way! Aluminium! Aluminum replacement
- Q:CSOL how do you use the cooling pipe?
- 4 cooling pipes, there is a different color, there are wood there? 3 for the green light. Don't move that different. There's a hint to press that different one! You can press infinity to spray cold air indefinitely!
- Q:How can the cooling water pipe of intermediate frequency cabinet be connected? What's the law?
- Medium frequency electric furnace on the bar, silicon controlled water jacket is a one in, out of the induction coil is also, the induction coil like the shape of the spring, draw a map of their own, under analysis, huh, huh. If not, take it off
- Q:In what circumstances should mass concrete be buried with cooling pipes?
- If the heat is too great, the external facilities can not guarantee the temperature difference between inside and outside, and the cooling pipe can be embedded.The commodity concrete pouring starts after finishing collecting, controlling the surface shrinkage crack, reduce the evaporation of water, and after the final setting of concrete began to cover maintenance, general merchandise within 12h after the concrete pouring and curing insulation covering, covering two layer straw bags, around two pile caps and surface layer of nylon film, straw bags under staggered, overlapping, open all the surface covered, forming a good insulation layer, and should be kept in a nylon film condensation water.
- Q:How to scale the cooling water pipe of vacuum pump reducer?
- Descaling ultrasonic, high pressure water or chemical reagents, descaling has not used, just know so many methods of descaling, or simply replace the tube to measure the economy of yourself!
- Q:How to decorate the mass concrete cooling water pipe
- Cooling water pipes are not generally advocated! (because partial cooling is not enough after hydration), a temperature hole is set for observation: as long as the temperature difference between the inside and outside of concrete is not more than 25 degrees, no measures should be taken! If the temperature difference is too large, you can take insulation measures (also ensure that the temperature difference is not greater than 25 degrees)This should be the construction team to consider the matter, the design institute will not consider this, are generally handed over to the construction unitThe purpose is to take away the temperature rise of cement hydration in time, and there is no need to do any calculation. According to the water temperature changes during construction, it is good to arrange the water flow
- Q:What is the biggest difference between a plastic cooling pipe and a serpentine pipe, like a serpentine one? Are they all used on machine tools?
- The 1. steps are: 1. General introduction. The necessary tools / raw materials, methods / procedures, points for attention2. common sense: answer the questions directly. Give specific reasons / reasons / introductions in detail3. reasons: 1. Explain the cause / reason in detail. Provide effective solutions (structure, see procedure class)4. other types see high quality standards
1. Manufacturer Overview |
|
---|---|
Location | Shandong,China |
Year Established | 2009 |
Annual Output Value | |
Main Markets | 30.00% Mid East 10.00% Southeast Asia 10.00% South America 9.00% Oceania 9.00% North America 8.00% South Asia 6.00% Eastern Asia 5.00% Western Europe 5.00% Eastern Europe 3.00% Northern Europe 2.00% Central America 2.00% Africa 1.00% Southern Europe |
Company Certifications | ISO 14001:2004;IQNET |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | Qingdao,Ningbo |
Export Percentage | 51% - 60% |
No.of Employees in Trade Department | 15 Day(s) |
Language Spoken: | English, Chinese |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Rubber Foam Heat Insulation Tube
- Loading Port:
- China Main Port
- Payment Terms:
- TT or LC
- Min Order Qty:
- 20 Cubic Meters m³
- Supply Capability:
- 200000 Cubic Meters per Year m³/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords