33114 Tapered Roller Bearigs Bearings Single Row Bearing

Ref Price:
Loading Port:
Qingdao
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
500000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specificatioin of Taperder Roller Bearings:



The tapered roller bearing is to bear the combination of radial and axial load but mainly afford radial load. The loading capibility is determined by the raceway angle of outer  ring, the larger angle afford larger load. This kind of bearings can be  seperated and it can be divided into single-row and double-row tapered roller  bearings by the number of columns. The clearance for single-row tapered roller  bearing should be adjusted by the customers when installation. For the  double-row tapered roller bearings,the clearance has already set by the  manufacture before ex-factory. Tapered roller bearing has taper shaped inner  ring and outer ring raceway,and the roller elements arrange between them. All  projection lines from the surface of rollers meet at the same point on bearing  axis. This design makes tapered roller bearings particular suitable for combined  (axial and radial) loads.The axial loading capacity is determined by the  contacting angle α, the bigger angle for α, the larger axial loading capacity  is. Tapered roller bearing is usually a seperated bearing, that is,the inner  ring assembly including roller and cages, is seperated installed with the cup.



Taper roller bearings are mainly used for radial and axial joint load with radial load as main subject. Axial load capacity relies on raceway angle of outer ring: the bigger the angle is, the bigger the bearing capacity is. Outer ring can be separated and can be easily assembled. During installing and using process, axial clearance and radial clearance and radial clearance can be adjusted and pre-interference installation can be allowed. 


            


Product application:

In many applications tapered roller bearings are used in back-to-back pairs so that axial forces can be supported equally in either direction.


- car and vehicle wheel

- mining equipment

- moderate speed

- engine motors

- axle systems    

- construction

- agriculture

- reducers

- gear box



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:There is a slot in the inner ring of tapered roller bearings, right? Is the roller in the slot?
There is a slot in the cone... The ball is placed in the slot. Handan, north, LiAskIs there a gap between the roller and the slot?Can I move axially?Chasing the answerThere is a certain clearance between them. It is not very large. It is caused by the force...
Q:What is the size of tapered roller bearings 352214?
Bearing type: tapered roller bearingNew model: 352214Old model: 97514EInternal diameter (mm):70Outside diameter (mm):125Width (mm):75
Q:What items should be inspected for tapered bearings?
1, the tapered roller bearing without cracks, sharp edges, plants and rust; on the road has not agreed to the raceway of machining trace; super fine traces in the outer ring, the steel ball surface should be symmetrical task differences, not to have scratches, bumps;
Q:Small problems of roller bearings of tapered roller bearings
Tapered roller bearing roller must have certain taper roller and raceway, inside and outside the vertebral vertebral vertex vertex must be of the same point and in the shaft center line (similar to bevel), or when the roller bearing motion reducer and raceway for angular velocity, linear velocity will be the same for different sliding friction and rolling bearing becomes sliding bearing.
Q:Tapered roller bearing: Bearing expert why burned or locked
2, the bearing seat hole size deviation is too small or the size of the shaft deviation is too large, extrusion bearing ring deformation, make the clearance smaller. To burn locking phenomenon.3, bearing outer diameter and bearing seat hole, or between the bearing bore and the surface of the shaft between the foreign body, such as iron filings, burr, sand, cotton and so on. Will also squeeze bearing deformation, so that smaller clearance. To burn locking phenomenon.Bearing burnt lock. The cause of the accident can be analyzed according to the burning degree of the inner shell, the outer shell and the roller1. The inner shell burns most severely, the roller slightly lighter, and the outer shell almost does not change. After excluding the reasons for the nonstandard size of the inner bearing housing, the following judgment can be made.
Q:Internal and external tolerances for tapered roller bearings?
There is one thing that measures the inner diameterPlug coneThe outside diameter of the tool has not been seenThe tool set up is the watch standYou check it outIs it too troublesome to check each one?
Q:Can tapered roller bearings be joined together with two single row tapered roller bearings instead of double row?The altar,
3, load and life usually do not vary greatly, this is a personal opinion. I hope I can help you!
Q:Tapered roller bearings, 70 in diameter, please tell me the model number
What about outside diameter (D) and width (B)? You didn't say?.Following are all series of codes and sizes for tapered roller bearings (single column and double row). I hope they can help.Single row tapered roller bearings (taken from GB/T 297-1994)Bearing code |30000: 32914 X2Basic size /mm|d: 70Basic dimensions /mm| D: 100Basic size /mm|T: 20Basic size /mm|B: 19Basic size /mm|C: 16Installation size /mm|da (min):-Installation size /mm|db (max):-Installation dimension /mm| Da (min):-Installation size /mm|Da (max):-Installation size /mm|Db (min):-Installation size /mm|a1 (min): 4Installation size /mm|a2 (min): 6Installation size /mm|ra (max): 1Installation size /mm|rb (max): 1The other is /mm|a size: 19Other sizes /mm|r (min): 1Other sizes /mm|r1 (min): 1The calculated coefficient is |e: 0.33The calculated coefficient is |Y: 1.8The calculated coefficient is |Y0: 1Basic rated load /kN|Cr: 53.2Basic rated load /kN|C0r: 85.5The speed limit / (r/min) | fat: 3600The speed limit / (r/min) | oil: 4500The weight is /kg|W:-
Q:Method or tool for measuring clearance of tapered roller bearings.
This should be accomplished by tightening the clearance of the gear box end cover.
Q:How does the roller of tapered roller bearings fit in?
Tapered roller bearings itself can be broken down, and new (or old) bearings are cleaned and decomposed. So do not worry, carefully installed in accordance with the original installation order on the line, and if it does not meet the installation order, the installation of this bearing is not go on.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range