metal coils slitting line
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Features:
1. The production line is a thick metal coil leveling and cut into a massive of special equipment. Usually cited by the feeding car,uncoiler,pallet pressure device,leveling host activitiesacross the bridge,guide corrective device,length agencies,film equipment,shear,conveyor table,pneumatic discharge rack,hydraulic lift the composition of the pile material, material transport roller and hydraulic system,electrical control system, the concerted action of PLC control. The main hydraulic,pneumatic and electrical conreol components,cot to length system selected international brands.
2. This equipment is mainly used for processing cold-rolled carbon,stainless steel coil, and non-ferrous metal coil, configuration,six leveler to theentire pacification of long shear plate surface of the metal aluminum and other high coil.
3.According to customer requirements, the fine two leveler can be used early; fixed length sent to shear can be ordinary mechanical appliances collaborative action, digital variable frequency or AC servo technology; shears can be equipped with the ordinary machienry, hydraulic press type electromagnetic clutches,pneumatic clutch transmits power high speed gate shear, mobile tracking the chase cut and rotary flying shear machine. Supporting related molding machine can be used for a wider range extension.
I. Technical Data
Technical data for KJS180 series | ||||||
model | thickness(mm) | width(mm) | slit number PCS | Accuracy (mm) | Speed (m/min) | weight (t) |
KJS180-1*650 | 0.2-1 | 150-650 | 30-8 | ±0.05 | 0-180 | 3,5 |
KJS180-1*850 | 0.2-1 | 300-850 | 30-8 | ±0.05 | 0-180 | 5,10 |
KJS180-1*1050 | 0.2-1 | 300-1050 | 30-8 | ±0.05 | 0-180 | 5,10 |
KJS180-1*1300 | 0.2-1 | 400-1300 | 30-8 | ±0.05 | 0-180 | 10,15 |
KJS180-2*650 | 0.3-2 | 150-650 | 30-8 | ±0.05 | 0-180 | 3,5 |
KJS180-2*850 | 0.3-2 | 300-850 | 30-8 | ±0.05 | 0-180 | 5,10 |
KJS180-2*1050 | 0.3-2 | 300-1050 | 30-8 | ±0.05 | 0-180 | 5,10 |
KJS180-2*1300 | 0.3-2 | 400-1300 | 30-8 | ±0.05 | 0-180 | 10,15 |
KJS180-2*1600 | 0.3-2 | 400-1600 | 30-8 | ±0.05 | 0-180 | 15,20 |
KJS180-2*2000 | 0.3-2 | 500-2000 | 30-8 | ±0.05 | 0-180 | 15,20 |
KJS180-3*1300 | 0.4-3 | 400-1300 | 30-6 | ±0.05 | 0-180 | 10,15 |
KJS180-3*1600 | 0.4-3 | 400-1600 | 30-6 | ±0.05 | 0-180 | 15,20 |
- Q:What is the surface rolling forming machine process?
- The rolling process using metal at room temperature, cold plastic characteristic, through the rolling tool is the rolling tool to put some pressure on the metal surface, so that the workpiece surface by plastic deformation, the height to the lower tissue slip, the surface roughness decreased.
- Q:Improvement in rolling forming process
- The rolling will produce a hardening layer on the surface of the workpiece. This layer has obvious delamination phenomenon with the internal material, which is easy to cause the surface layer to fall off;
- Q:A roll forming machine, rolling out of the length is always not up to a fixed size, not too small, that is, more than that, what is the cause?
- Yes, the width of the bearing plate can be a deviation from the length.
- Q:What kind of material and what heat treatment are used for pressing roller (molding, feeding, cutting force, heavy load, heavy load) of sheet steel rolling machine?
- Use 40Cr or 20Cr, Cr12.Cr12MoV, quenching and tempering treatment, think of hardness, high point, carburizing, nitriding, and consider adding lubrication device to extend its service life
- Q:Process mould for rolling forming process
- Rolling forming is more complicated and requires higher than rolling thread. The die design is based on the different shapes of the workpiece, the design of the rolling plate into a cross section or a few sections, can use synchronous type; also can use grading type.
- Q:What is rolling forming processing?
- Ironing the surface of the workpiece with a raised micro wave crest to fill the concave micro troughs, thus changing the distribution of the peaks on the surface, and obtaining smaller surface roughness values.
- Q:Material and equipment for roll forming process
- Rolling process is a cold forging process, which can be used for rolling and forming a lot of materials. Among them, low carbon steel is a material commonly used in rolling forming, and non-ferrous metal is more suitable for roll forming.
- Q:Introduction of roll forming process
- Roll forming began around 1960s in europe. Because of roll forming, the working model has the advantages of high production efficiency, saving material and increasing product strength.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
metal coils slitting line
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords