Corridor bathroom LED0.6 m T8 lamp radar
- Ref Price:
-
$3.88 - 4.27
/ pc
- Loading Port:
- Hong Kong
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Specification
Corridor bathroom LED0.6 m T8 lamp radar
LED T80.6 Mi Leida lamp is intelligent energy-saving lamps, suitable for indoor walkway, toilet, when a person enters the radar sensor area, the lamp lights up when the sensor out of the area one minute, the lamp will automatically turn off. Enter the sensing area (6-9 meters), it is all light (9W), leave the sensor area, it is dimly lit (2-3W).
Tube specifications for the 9W, its technical parameters are as follows:
No. | Name | Parameter |
1 | Product Size | 28.5mm*33.0mm*586mm |
2 | Light Source Type | LED 5730 |
3 | Electric Source | Isolated Power Pass CCC,CE Certification |
4 | Color Temperature | 5500K-6000K |
5 | Power | 9W |
6 | Input voltage | 220--240V50 / 60Hz |
| 7 | Power Factor | ≥90% |
8 | Light efficiency | 88LM / W or more |
9 | CRI | ≥80 |
10 | Protection grade | IP20 |
11 | Irradiated area | 20square meters - 25 square meters |
12 | Scope | applicable to the underground garage, corridors, toilets, basement, garage, warehouse, office and other energy-saving automatic lighting occasions |
13 | Warranty period | 2 years |
Our business philosophy is"people-oriented, technology-first", "quality first, service-oriented" . environmental care into product designs - create a bright and beautiful, and dedication to provide customers with cheap and quality lighting products service, warmly welcome new and old friends at home and abroad patrons.
- Q: Can fluorescent tube T5 and LED T5 be connected in tandem?
- The main difference is the support of built-in and interfaces, such as fluorescent T5 is to use electronic rectifier, LED with constant current device, etc., don't change stent must not, even the stents in together, must be allowed, are in parallel in the circuit.
- Q: The two ballast that originally was electric inductance towed three ordinary fluorescent lamps, now changed to LED fluorescent lamp tube, have influence?
- You slam the door of the original circuit, LED fluorescent tube is in with the drive, as long as according to the directions, the wire connected, the zero line of the original circuit is a traditional fluorescent lamp ballasts, and LED is not the same, so you can cut down, the original circuit directly connected to your leds.
- Q: Put on the new light bulb, why the lamp still not bright
- If there is a problem in the ballast itself, if the lamp filament of the inductor is red but can not be activated, most of the regenerator short-circuit damage.
- Q: The ordinary fluorescent lamp in the home is on the Internet say to remove the hui, the ballast part is short, put on LED lamp tube, can connect to change 3 lamp tube not bright?
- Tear down, the starter of the ballast two wires together is short circuit, and then mount LED bulb, then spin the tubes card in place, above if no problem, so there is no possibility of three light tube is not bright.
- Q: The difference between the Ledt5 lamp and the temperature 3000k and 2700k
- 3000k lamp tube luminescence is white point, 2700k lamp tube illuminant red a dot.
- Q: How much is the ballast of the fluorescent tube coming out
- The fluorescent lamp ballast is not to be understood by the idea of the current when it is activated in the lamp tube. The lamp tube of different wattage matches the current of the ballast of different current and the current is too bright or hard to start. Inductance ballasts, for example from 8 w15w20w30w40w when it in tubes without ballast between the output voltage and the zero line is power electricity after being connected in good tubes start according to the voltage at the ends of the lamp power different lamp in 80-110 - v, about 40 w at the ends of the tube voltage 110 v. Electronic ballast is the principle of the second inversion of high frequency oscillation. The output power is achieved by the size of the current supplied by the booster coil. The single-strand wire of the 13W booster coil is made, 25W with a two-ply line of 36W with 3 strands of 55W with 7 strands of gauze, the more power the larger the need of the current. Because of using ordinary multimeter is not suitable for testing the high frequency alternating current (ac) in maintenance electronic ballast can be ignored when the output voltage and to detect components mainly including tubes.
- Q: What is the minimum starting voltage for the fluorescent tube?
- The minimum maintenance of a fluorescent tube is 100V volts. 2 · the fluorescent lamp is in qi hui instant, the rectifier load voltage is 800 volts. (the function of the ballast). This 800 volt voltage is transient and can be observed with a digital oscillograph, and the 800v voltage is observed through the digital oscilloscope. I don't have any real data.
- Q: What does philips mean by TLD36w / 54-765
- Yeah, I did it for you, I think it's the bottom, Let's see if it is ~ TLD ~ T8 Dailyght 160-240v (model) 36 ~ 36 w.I hope my answer will work for you.
- Q: How is the T8LED fluorescent lamp installed?
- If it is old fashioned, you must cut the input of the ballast and install it as shown below.
- Q: Does daylight bulbs damage electronic lamp heads?
- Will you get the power wrong? Maybe there's some protection on the lamp that the developer has lost, if you're the new one, you're going to go to the dealership.
Send your message to us
Corridor bathroom LED0.6 m T8 lamp radar
- Ref Price:
-
$3.88 - 4.27
/ pc
- Loading Port:
- Hong Kong
- Payment Terms:
- TT or LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
Hot products
Hot Searches
