T8 LED Tube SMD Chip High Efficiency 1.2M 15W

Ref Price:
$8.07 / pc
Loading Port:
Payment Terms:
Min Order Qty:
10 Pcs pc
Supply Capability:
100000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

T8 LED Tube SMD Chip High Efficiency 1.2M 15W 1. This product meets the standard of CE certification.
2. With internal No-isolated power supply.
3. Round and the elliptical tube are available.
4. Use the most mature international well-known LEDSMD2848 as the light source, which can ensure the led tub35 as the light source, which can ensure the led tube brightness and long lifetime, also can reduce the light decay.
5. Use the high quality aluminum PCB for LED’s better heat dissipation.
6. High-grade PC cover with nice light transmittance(> 95%),Transparent PC cover and frosted PC cover are available.
7. 180 degrees beam angle makes the lighting effect better.
8. CRI(standard products)>70,it can be over 80 if required.
9. Ambient temperature:-20°C-40°C, surface temperature: 42°C-45°C
10. No mercury, lead or other hazardous materials; no radiation, no electromagnetic radiation, no frequency flash, instant start up, no hurting eyes.
Replacement for conventional fluorescent tubes:
1. Hotels
2. Conference/ meeting room
3. Commercial Complexes
4. Residential/ Institution Buildings
5. Schools, colleges & Universities
6. Hospitals General li

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Are led fluorescent tubes not available for lighting?
If home have a stent is built-in LED lights to be the most is to take the rectifier, and the external power supply is to use the power of the manufacturer to provide, so to be more back to safe some more energy efficient, at the same time LED the longer service life
Q:Is the normal daylight tube replaced by an LED line
Step 1: use a screwdriver and a pliers to disconnect the ballast from the wire. But my home is the sun lamp base of zhengtai, the quality is too good, it took 10 years. I didn't even get down to the ballast, which was stuck in a full thick iron base, so I disconnected the wire. The wire that disconnects from the ballast is sure to have two heads, just to disconnect the connection. There is a lot of direct skewers of black tape, some of which use that connector and screw the two wires together. It's the same thing. This is the connector that is used in this case. Disconnect the regenerator, remove the wire and then rewire the two broken wires together and attach the black tape (which is the insulating tape). Put the base back to the original. Install the fluorescent tube, and remember to place the head of the European logo on the base of the current. And when you put it in place, it's going to be OK.
Q:What are the types of leds?
Now the most common in the market is T5 integrated fluorescent lamp, T8 sub-standard, T8 integrated fluorescent lamp, three kinds. The length is 30cm, 60cm, 90cm, 120cm, 150cm, etc. There are also T4, T6, T10, etc. These specifications are rarely used in LED fluorescent lights. Please accept your satisfaction Is that ok?
Q:Daylight lamp tube is broken, does not clean can be bad? In the office
It contains mercury vapor, which is bad for the airway, and it's better to disturb, not to smell
Q:If you want to replace it with an LED fluorescent tube, how many watts does it take?
Commonly used household generally is 1.2 meters, is a traditional fluorescent label 36 w, combined with the actual total power dissipation of the ballast at about 40 w. If replace with LED fluorescent tube, 18 w is enough light. Such as check brightness demand is not high, some useful also 16 w to replace.
Q:Why don't leds need a rectifier
LED is a dc device, and the driver must be different. If you do not remove the rectifier, you may not install the LED lamp.
Q:If the body is accidentally broken, will it be electrocuted?
No, only a small amount of fluorescent powder and gas will be slightly contaminated with the environment
Q:Do not have the fluorescent lamp of actuator, how to change LED lamp tube?
To replace the fluorescent lamp ballasts with constant current power supply LED lamp, the lamp again feet according to the requirement of the tube is connected to the power supply is ok, there are several kinds of LED bulb light foot, according to the actual wiring, general instructions are on the tube.
Q:How to replace old lamp tubes with LED tubes
The leds that appear on the market today should be connected directly to the 220V power supply. The power supply and the lamp are together.
Q:Use LED fluorescent lamp tube to replace, the line of original daylight-tube seat should be refitted
So old ballast, the ballast uninstalled, directly to the card on the two old fluorescent lamp wire short respectively, and then to the outside power, install the LED fluorescent lamp with respect to OK
We are a leading manufacturer of a broad range of LED strip light and LED Tube light. From 2011, we have integrating sphere spectrometer, high speed automatic placement machine, reflow soldering machine, automatic dispensing machines and other specialized equipment and professional R & D department. LED strip light can produce up to 300000 meters per month.

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2011
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 20 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 5
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap