Q:Water heater hose 4 points and 6 points difference

1 inches =25.4mm, 4 points hose is DN15 pipe, that is, the inner diameter is 15 millimeters, 6 points hose is the diameter of 20 mm tube, 5 to 4 hose, you should say that the variable hose hose is divided into: stainless steel. Divide 1 inches into 8 parts, eight in 49, four in charge, and 6/8 in six.

Q:Is the electric water heater well connected with the metal hose?

It's better to use a metal hose.Good resistance to high temperature.In addition, the metal hose is better tolerated.It is more durable and difficult to break than hose.

Q:How to install the water hose and do you use the tape? Or direct installation?

Installation of water hose, joint with PVC (or metal pipe) head, the end of the connector with 8 iron wire at least two tied, and tied together at the end of a piece of wire;

Q:What is the principle of communicating devices? What if the rubber tube is used as a connecting device to change the water for the fish?

The principle of communicating devices can be explained by liquid pressure. If the same liquid is contained in a U glass tube, a small liquid AB is conceived at the center of the bottom of the communicating device. If the liquid is stationary, it does not flow. The pressure of the liquid in the left tube toward the right side of the liquid AB must be equal to the pressure of the liquid in the right tube toward the left of the liquid AB. Because in the communicating vessel is filled with a liquid, the same two liquid column density, according to the formula of P= P GH liquid pressure that only when both sides is equal to the height of liquid column, the liquid column is equal to the pressure on both sides of the liquid film AB. Therefore, in the case of no flow of liquid, the liquid level in each vessel of the communicating device shall be kept flat. (ideal model method) the connecting device is characterized in that the liquid level in each container is flat only when the same liquid is contained in the container. If the container is tilted, the liquid in each container is about to begin to flow. One end of the liquid column flows to the lower end of the liquid column and stops flowing until the liquid level in each container is normal. As with rubber tube two glass tubes connected together in container with a liquid, which will be a fixed tube, the other tube up and down or tilt, can see the two tube level in stationary phase remained flat. The connecting device is provided with the same liquid, but the pressure on the liquid surface is unequal, and the pressure difference of the liquid surface is equal to the pressure difference produced by the liquid level difference of the two container of the communicating device.

Q:How can the rubber tube be used properly and how to use it properly?

Hose selection and installation caused by improper hose rupture. When replacing the hose, the hose wire length, number, shape and size of the joint should be reasonable, and should try to reduce the degree of bending in the hose; tighten union nut, do not make the hose distorted, excessive bending and twisting will reduce the service life of the hose greatly; some easily friction parts should take protective measures to prevent the hose due to wear and burst.

Q:The difference between the rubber pipe and PE pipe

The characteristics of the rubber tube has physiological inertia, UV resistance, ozone resistance, resistance to high temperature (-80 to 300), high transparency, strong resilience, resistant to compression permanent deformation, oil resistance, impact resistance, acid and alkali resistance, wear resistance, flame resistance, voltage, electric.

Q:Stainless steel metal hose and flexible rubber joint which is easy to use?

The pressure and temperature bearing capacity of the stainless steel metal hose shall be due to the rubber joint, and the length of the product can be customized according to the requirements of the field, and the form of the joint is very rich.

Q:What material is used in the gas pipeline to reduce the wastage?

The inner layer and the outer layer plastic tube is a kind of special polyethylene material, non-toxic environmental protection and quality of light, the nature "is very suitable for application can take temporary setbacks" in the home decoration. But as aluminum pipe of indoor gas pipe, can withstand the pressure of work, but also because the pipeline can be extended for a long distance, need the joint is less, so the gas permeability is almost close to zero. Using aluminum pipe owners as household gas transportation route is safe and reliable, but be careful to avoid buy inferior aluminum-plastic, because the market inferior aluminum pipe by the collision, easy bending, deformation, or even rupture, threatening the safety of life and property owners.

Q:My company does high-quality rubber tube, all of the core method, and why use EPDM to do the inner tube, it is difficult to take off the core, please point out! What's the reason?

Hose core need special tooling, EPDM mandrel and rubber vulcanized rubber tube together will produce covulcanization phenomenon, easy to produce adhesion, so need special disposal to complete stripping, and should adopt non core industrial processing, I is a professional manufacturer of automobile rubber tube there is not clear I can ask each other AC.

Q:Is hot melt hose toxic and harmful?

The heater adopts the U.S. and high temperature heating wire line, uniformly wound around the pipe wall, with thermal insulating properties and uniformity, good heat resistance, heat insulation material of high quality, ensure that the insulation performance of larynx.