Self-propelled aerial working platform PSS500A

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:


Model
PSS500A
Working heightmabout 50.00
Platform heightmabout 48.00
Working radiuscapacity 200kgmabout 17.10
Working radiuscapacity 80kgm20.00
Platform capacitykgMax 200
Cage rotation angleabout 180
Platform dimensionsL*W*Hmabout 1.20×0.80×1.10
Outrigger sizem5
Lengthmabout 8.30
Widthmabout 1.58
Heightmabout 1.98
Pressure on earth(working)Kn/m3.9
Pressure on earth(traveling)Kn/m4.8
NWkgabout 13500
Range of rotationabout 450(noncontinuity
Range of wireless remote controlm100
Motor
Diesel 380V


- Long working radius
- Electrohydraulic proportional control
- Hydraulic outrigger can separately control.Outrigger balance by itself
- Cage can rotate 180∑
- Fuzzy walking technology
- The height and width of track is adjustable, it can travel on any unevenness road
- Outrigger can level by itself;
- Rubber track has little pressure on earth, it can travel on any ground
- Small when it retracts,nimble

The right of changing specification and design is reserved

Optional configuration
- one or two colors;
- seat belt;
- PVC outrigger pedal;
- plastic pedal;
- non marking tyre


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do you remove the horizontal universal elevator milling cutter
Tie rod and the threaded part of the milling cutter is too short, removing cutter bar back a loose, threaded connections even fewer number of buttons, easily when tapping threads dozen hair, and make the cutter not screw down, or make the damage of tie rod.
Q:How to use the elevator to be safer and more efficient
Monthly check Roller, shaft and bearing, oil cylinder pin shaft and bearing, arm hinge shaft and bearing, etc. All parts should be filled with lubricating oil to extend the life of the bearing. Oil and oil level of hydraulic oil. The platform rises all the way up, and in this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. The hydraulic oil is dark, sticky or gravel, etc. If found, it should be replaced in time (32 # hydraulic oil).
Q:How to maintain the platform?
Remove the hydraulic oil and remove the oil strainer, remove the oil strainer, clean it up, and then put it back in the tank and connect the pipe. (put on new oil and don't use the old oil. Otherwise, the moving parts of the hydraulic lift system will accelerate the wear and tear.) Remove and disconnect the lift valve, blow the plunger down with compressed air, then load and resettle. Check all hydraulic pipes and connectors. The pipe should not be broken, the joints should not be loose, and all the joints must be tightened.
Q:The advantages and disadvantages of using diesel engine as an engine
Most of the diesel engines are low speed machines, with a speed of about 100 revolutions per minute, which can drive the propeller directly. Improved fuel consumption of diesel engine power plant to the lowest, and lift platform can use cheap residue, high reliability, the thermal efficiency can be closer to 50%.
Q:What is the main shaft of the horizontal milling machine
The main shaft variable speed has the impulsion device, facilitates the speed change, the machine tool can brake quickly and effectively. 4, machine tool of important transmission parts are made of alloy steel, easy to wear and tear of the parts are made of wear-resisting material, guide model, and the service life of the machine to have enough.
Q:Diablo ii flame volcanic mission will not be able to jump
Go to the end of the board and move to the top of the board, then move to the opposite side of the position, shift the shift and then move the space.
Q:The hydraulic platform is compared with the normal lift platform
Double protected leg structure, work safer, and can be close to the working face lift. The machine is the answer for you!!
Q:The structure of the universal elevator milling machine
The main shaft is used to install the tool pole and rotate the milling cutter. The main shaft is a hollow shaft with a 7:24 precision taper hole in the front, which is used to install the taper shank of the milling cutter. The longitudinal platform is carried by longitudinal screw, which is carried on the guide track of the turntable, and the workpiece on the surface of the table is moved vertically. The T groove on the surface of the table is used to install the fixture or workpiece.
Q:The purpose of the rail elevator
Guide lifter is a kind of hydraulic elevating shear machinery and equipment. Used for secondary and tertiary industrial workshop, restaurant, wine shop floor between the transport of goods. The minimum height from 150-150 mm, optimal it is suitable for the workplace can't excavation pit. And do not need the upper lifting point, in the form of diversification (single column and double column, the four pillars). Equipment running smoothly, guide of elevator guide rail is commonly channel steel, H steel, square tube welding, operation is simple, reliable and convenient transport of goods economy.
Q:How to improve the oil leakage line
If it's an interface leak, you need to check if the interface is loose and the seal is broken. Or the interface design is not reasonable, you need to improve the interface.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range