Q:What kinds of tables are there? Which is better for the office?

Lift table many brand, currently on the market the main lifting table is divided into: electric hoist, mechanical lifting table (barometric, mechanical lifting), electric lift table when the disadvantage is that there was no electricity can't use our company with polly lifting table, manual lifting regulation, any place to stay, very effort; And it can move back and forth

Q:The advantages and disadvantages of using diesel engine as an engine

The fuel consumption is significantly lower than the steam engine power plant. Economical and practical, diesel fuel is low in the same kind of fuel, so it is easy to accept.

Q:How does the table in the middle of the tatami mat go up and down

Need to buy the metal platform of suitable height, use screw to install small table board. Steps are as follows: Installation: desktop lock desktop board with screws on the top of the lifting platform (such as manual lifting platform should be first in the middle of the desktop is boring, the size of the hole to match the rocker tank size).

Q:Which is good for mobile goods elevators?

The design load of all mechanical and transmission equipment of the hoist is more than five times the actual load. It is a safe choice for you to go to jinan

Q:Is there a replacement for similar elevating functions?

This is not a press machine, a wacky experiment, a big nail in the press, and how much pressure to puncture a tyre.

Q:Tomb raider 9 research base elevator to go to go to go to go to the order to pry the gear not to go down to go down to go down the card 3 to break up

Press the switch and then descend the elevator down to the second floor and then climb to the right hand side of the cargo and pull down the first gear. Walk to the elevator and climb down the stairs to open the door between the second and third floors. Go up to the third floor and turn the elevator to the third floor. And then you go back to the second floor and you go to the third floor and you go to the sandwich and you get the second gear. Go up to the fourth floor and press the elevator up, go back to the third floor and switch to the three or four floors and twist the third gear. Come down to the entrance of the third floor elevator and then go in and use a shotgun to smash the three floors and the four floors. On the fourth floor elevator again back to the fourth floor, between the back to the fourth floor on the elevator by just open the channel on the wall opposite the detour to the fourth floor mezzanine dropped last gear lever.

Q:How about customizing a tatami mat?

However, the tatami mat is no longer a problem. In a small room decorate a lifting platform tatami, not only improve the utilization rate of the space of the room to receive and we have guests home, tatami is lifting platform rises is a piece of tea table; Descend, and the tatami of the ground to be an organic whole, spread the mat of above a mat of a mat of a mat of a kind of a very beautiful bed. This can not only be used to make tea room, room, study, also can be used as a child's activity place, a room can use more.

Q:How does the platform maintain

Inspect hydraulic oil and oil level. The hydraulic oil should be 40 to 50 mm above the tank when the platform rises to the highest. When the oil is dark, the oil is sticky, or the oil has grit and other foreign things, the hydraulic oil should be replaced in time. The hydraulic system of lift platform applies 32 # hydraulic oil. A. check the hydraulic and pipe joints. The pipe is damaged and should be replaced immediately. Tighten the joint when the connection is loose.

Q:Safety operation of hydraulic platform

4, rise and fall: press the "rise" button, start the motor, the motor spin, the hydraulic system work, the oil cylinder protruding, the platform rises. Stay up to work the required height, "stop" button, the motor stop lifting platform, can work, if not in accordance with the "stop" button, the platform to calibrate height be 8 meters (native) trip switch, platform in height. At the end of the work, press the "drop" button, the solenoid valve action, when the oil cylinder is turned on, the platform is lowered by itself. During the use of hydraulic platform, it is strictly forbidden to overload (the unit load is 300kg), and the operator on the platform will not be moved during the descent. When moving or traction hydraulic platform, the supporting leg should be collected and the platform will be lowered to the lowest position. 7, when platform malfunction cannot work normally, should be promptly cut off the power supply for repair, it is strictly prohibited to equipment to work, in spite of non-professional workers do not remove the hydraulic components and electrical components. Do not use the machine in an unstable condition on the ground. Please do not raise the platform without the platform, the outside legs are not adjusted, the platform is flat and the ground is unstable.

Q:How to automatically lift up and lift

There is a manual lifting table, with the hand rotating black knob, lifting the platform clockwise, reducing the counterclockwise elevation.