Q:Excuse me, how can I get waterproof wires in the water?

35kV and below in low voltage cable joints if needed in the operation of the water environment, please do waterproof seal in the joints, joint can be orderly wound waterproof tape, heat shrinkable tube ends after heat shrinkable pipe shrinkage sealant, waterproof seal, installation conditions outside the FRP shell, shell insulation waterproof sealing glue perfusion. If the ordinary rain prevention, joints at both ends of the sealant after the root shrink heat shrinkable tube, heat shrinkable pipe mouth, waterproof belt, +PVC belt sealed!

Q:The function of rubber joint?

After installation, the transverse, axial and angular displacement of the pipe vibration can be absorbed. The pipe is not concentric and the flange is not parallel

Q:What is the difference between plastic lined steel pipe and rubber lined steel pipe?

Difference1. processing technology:Rubber lined steel pipe generally adopts the manual adhesive, vulcanizing process (can also be cold bonding operation); plastic lining pipe generally adopts the heating equipment, the overall rotational (tight loose lining, lining, molding, molding) main process steps can be completed by means of equipment. Therefore, the production efficiency of the lining pipe is obviously higher than that of the lining rubber tube.2.: the physical properties of rubber lined pipe due to the inheritance of the excellent properties of rubber, the chemical corrosion and wear resistance, heat resistance is also very prominent, and the plastic lined pipe in addition to resistance to chemical corrosion and lining hose close to the outside, in the wear resistance, heat resistance and adhesive strength are not as lining hose.

Q:Why should liquefied petroleum gas use strong rubber hose and liner?

Commonly called liquefied petroleum gasMain ingredients: ethylene, ethane, propane, propylene, butane, butene, etc. (oil resistance will accelerate swelling and aging).Appearance and properties: colorless gas or yellow brown oily liquid, has a special odor.In order to remind people of the leakage of liquefied petroleum gas in a timely manner, the processing plant often mixes a small amount of foul odor mercaptan or thioether compounds into liquefied petroleum gas, which is the source of special odor.These gases on the rubber has a certain corrosion, swelling (not resistant to oil will speed up swelling), aging effect, liquefied petroleum, so choose rubber seal to consider oil resistance, corrosion resistance, swelling!

Q:Can the spring hose joint be connected to the tap?

Two treatment1 if Water Leakage can choose to replace the elbow elbow, the best selection of true Shide profiles or fittings2 if the ground is Water Leakage, nine in ten was a cause of the pipe in the ground before the hot melt glue of the elbow. Then have to ask the property or a professional plumber to weld.

Q:How to determine the tensile strength of GB rubber joint?

The cutting of sample can be done by punching machine. When punching sample, the following points should be paid attention to.The cutting force is uniform, not too large, and with mild soap and water and clean tap water wet specimens (or tools), if a sample cut down, it should be abandoned, not to repeat the old mark for cutting.The direction of specimen cutting should be consistent with the direction of tension and the direction of rolling.

Q:Between the two flanges in the middle of the rubber tube, what is the name of the connection?

The product is mainly composed of inner and outer rubber layer, cord fabric and steel wire ring. It is formed by vulcanizing with metal flange at high temperature and high pressure

Q:Faucet hose connection problem

Ball valves can be made, but easy to leak. More than a few times to install a feeling, when the screw does not use brute force ah.

Q:The difference between the rubber pipe and PE pipe?

The appearance of the native HDPE is milky white and is somewhat translucent in the narrow cross section. PE has excellent properties that are resistant to most life and industrial chemicals. PE pipe welding, butt welding of PE pipeline, the method provides the highest reliability and the diameter of the range and pressure process: the end of the heating tube, using a tool called mirror contact pressure and temperature under the definition of "". The ends are contacted rapidly and remain under pressure during cooling. A medium density polyethylene pipe and PE pipe with high density polyethylene pipe. Divided into SDR11 and SDR17.6 series according to the wall thickness. The former is suitable for transporting gaseous artificial gas, natural gas and liquefied petroleum gas. The latter is mainly used to transport natural gas.

Q:Are the bridges, bellows and rubber tubes drawn out or are they drawn only? And the bellows are tensioned with the steel strand?

It is relatively rare, usually corrugated pipe for zinc metal corrugated pipe, the construction unit may be in order to prevent pipe blockage, when pouring concrete, the corrugated pipe with rubber tube, after pouring completed final setting, you can pull out rubber tube. Bellows need not be drawn.