PVC Conduit Reducer

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT or LC
Min Order Qty:
3000 Meters watt
Supply Capability:
300 Tons per Month watt/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

 

*High insulation, anti-current puncture strength

 

*Compression- and impact-resistant

 

*High oxygen value, good combustion resista

 

SPEC

(diameter)

Packing     pcs/ban

Thicknessmm)

Weight    g/m

Lenghtm

φ16

25

0.9

80

2-4

1.2

100

2-4

φ20

25

1.1

105

2-4

1.2

114

2-4

1.3

130

2-4

φ25

25

1.2

150

2-4

1.3

158

2-4

1.4

167

2-4

φ32

10

1.5

260

2-4

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Dark tube does not have any good way to resolutely?
And then another hook with a wire from the other end of the line into the mouth, according to the length of the first penetrate into the root, while the edge of the wire to do 360 degrees of rotation, according to feel or sound to confirm the two wires have been After twisting, slowly pull out, to the other one to bring out (Brought out of the head of the head out, with another root from the line, can not pull out too much) And then hang the wire to the left of a wire, tighten, from the other end of the wire slowly pulled out to pull the wire out to stop In the process of pulling out the wire or wire, the best someone else from the other side of the delivery, the two will be much better with the effect 2 Determine the direction of the wire tube, with the wire to the blocked position, in the wire to do the mark, pull out the wire, according to the length of the block to find the approximate location, and then cut the wall or ground inspection Repair the wire tube, into the wire after the repair decoration In the absence of a certainty whether the wire tube is really blocked, the previous method should be tested several times, and the method 2 should be used again
Q:Indoor dry bag type steel core power cable terminal what is the meaning
Network patch panels are currently five categories, six categories, shielding and non-shield-based, the port has 8.12.16.24.32.48.96 mouth, the international general line T568B, thank you!
Q:PCB shop when the grid grid width and spacing is generally how much? For example, the general single-chip learning board is generally how much?
Small audio, hard drive serial port parallel lines, crystal head, network clamp, line measuring instrument, memory card, card reader, CD, engraved system CD. You open this shop finally in the old some of the radio charging type, take a assembled computer or color page offer
Q:What can go to the top of the geothermal tube?
And then I have to do any height of the climb can be calculated very accurately. If you will draw a CAD drawing on the size of the next will be out if you are directly engaged in the installation of construction, according to the three functions can be considered an overview
Q:Cable 4x185 + 1x95 need a large trunking
. according to the national standard GB / T.1-2008 method of calculation, YJV-4X185 +1X95 nominal diameter of not less than 53.7mm, usually between 54mm ~ 57mm. . the cable has power cables, control cables, compensation cables, shielded cables, high temperature cables, computer cables, signal cables, coaxial cables, fire cables, marine cables, mining cables, aluminum cables and so on. They are composed of single or multi-strand wire and insulation layer, used to connect the circuit, electrical appliances and so on. . outside diameter wàijìng [outsidediameter; externaldiameter] including the thickness of the pipe or container, including the outer diameter.
Q:50 pairs of 110 wiring module how to apply quotas?
Wiring racks with integrated wiring in the cabinet, rack quota. The patch panels are used for end-user lines or trunks and are capable of deploying them. The patch panel is the most important component of the management subsystem and is a hub for cross-linking the two subsystems of vertical and horizontal cabling. The patch panel is usually mounted on a cabinet or wall. Through the installation of accessories, patch panels can meet the full range of UTP, STP, coaxial cable, fiber, audio and video needs. In the network engineering commonly used patch panels have twisted pair patch panels and fiber patch panels. According to the use of different locations, divided into the main distribution frame and the middle distribution frame two categories.
Q:Digital TV set-top box how to receive three wires on the TV
Small high-level must be the framework of the structure, so the walls are not bearing walls, walls only play a role in isolation. If the brick structure of the wall (that is, brick from the load-bearing role), brick above is not open horizontal groove. But you can open the vertical groove. Because the open channel wall collapsed.
Q:Consult N line is not considered current-carrying wire?
N line must belong to the current conductor. If the three-phase load balance, N-line current is . such as imbalance, there is a current through. Such as the third harmonic of the grid serious, N-line current may be greater than the phase current. At this point, the wire cross-section should be the current flow of N line selection. PE line should be non-current-carrying conductor.
Q:Is the cable model determined by the size of the current?
First of all from the construction point of view, high-voltage cable laying the upper layer easier, taking into account the heat.
Q:Ipad not charge how the matter. Said the cable or accessories have not been certified, and may not be able to cooperate with this ipad reliable work.
Right-selectnets, and then select the whole board box, or select the network you want to change the line width and then right -Properties ..., in the pop-up Properties dialog box you can fill in the line width value, it is possible to change the line width Will be violated, resulting in changes to failure, this time, you can press DRO no model command to prohibit the rules, and then modify the
Our company now has more than 100 employees, over 30 technicians and a professional technology R&D center. At present, our products has been proved up to GBJ15-88"Build water system design specification" standard.We welcome customers from the entire world to cooperate with us.

1. Manufacturer Overview

Location Guangdong,China
Year Established 2007
Annual Output Value
Main Markets South America
Eastern Europe
Southeast Asia
Africa
Mid East
Eastern Asia
Company Certifications CE

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage 51% - 60%
No.of Employees in Trade Department
Language Spoken: English, Chinese
b)Factory Information  
Factory Size: 3,000-5,000 square meters
No. of Production Lines 8
Contract Manufacturing OEM Service Offered Design Service Offered Buyer Label Offered
Product Price Range