Q:Ok, so I applied a bit too much pressure on my faucet handle in the bathroom sink and now when i turn on the water the handle is a bit loose. and i have to turn it a certain angle to shut off the water completely. I've notice that there is a little ring that is loose, any idea on how to fix this loose problem...

you will have to take the center cap off and remove the screw the handle is stripped take it to home depot or lowes and get a new 1. if its old enough that you cant find a new handle you can buy a new faucet and install it for under 30 bucks good luck

Q:I got a new faucet with sink and the faucet is not positioned over the drain, also water cloudy. Kindly advise...

your faucet does not need to be over your drain they can be anywhere you would like them. As for cloudy water could be something in your pipes or water system. It should clear back up after have had the water back on for while.

Q:Kitchen pots hot and cold faucet water hose connector how to unscrew? Nuts in the deeper position of the valve body, wrenches and stretch does not go, hand screw is not OK, too tight. Is the faucet with the hose connection joints, can only cut? Leading water leakage to change it. What tools are there?

First connect the hose and the angle valve with a wrench. And then move the handle in the direction of rotation, that is, to screw the direction of rotation, which is the faucet below the nut will be loose, holding a rag, into the pool below, touch the faucet nut, you under the nut. When the faucet will pull out the whole, and then I would not have to say it! The

Q:Taiwan basin with a single hole is good or three holes of the good, what are the advantages and disadvantages

From the operation, single-hole basin mixer, adjust the water temperature, the flow is more convenient, a handle can be adjusted. The adjustment of the three holes will be more trouble, to twist the two handles several times before it can be transferred to the appropriate temperature.

Q:Bathroom faucet is leaking. It has only one handle on it and you turn it left or right for hot or cold. Can I switch it out, easily, for a faucet that has a separate hot and cold knobs?

Yes okorder /

Q:I have a Kohler (sp) faucet in my master bath that's come loose. I've looked underneath for some kind of bolt to tight, but I don't see anything there to tighten. I'm wondering if it was fitted badly and the means to tighten it lays between the plywood and the granite top. Thoughts?

Because you'll NEVER get a standard wrench up in there (I've tried, trust me), you'll have to pick up a cheap basin wrench at your local hardware store. See below link for pic.

Q:i try to fix it myself.i can't seem to unscrew that white plastic ring, it was really tight. so what should i do now? should i hire a professional?

If your faucet is leaking out the spigot you're working on the wrong part of the unit. This is a tightening hold down nut that threads up onto the water feed pipe and is most likely corroded or rusted in place so bad that the only way to get it off will be to crack it with a cold chisel and twist it off, or get a Dremel tool with a cutter wheel on it and cut it off that way. Either way, wear safety glasses while removing it as rust particles in the eyeballs are not fun. If the leak was coming from underneath the sink, under the faucet, then yes, you'll need to replace the entire fixture. If you do, when you put it back together and put the new nuts on where this one comes off, put a little vaseline on the threads before you put the nut on, it will make it go on easier and certainly, if you ever have to do this again, it will come off easier.

Q:How to connect the water heater to the basin

In the water heater outlet connected to a T-type three links, so that hot water can be diverted, respectively, then shower (shower need to install the control switch), wash basin and kitchen.

Q:I purchased a new faucet with sprayer. Currently I have a faucet but no sprayer.next to where the sprayer should go, there is a overflow for my dishwasher. Do I need to drill another hole or do I need to do something with the overflow ?

You will need to drill another hole. The overflow you mentioned is called an Air-gap. It prevents the dishwasher drain from pulling a vacuum on the sink drain. They were required in some areas but now are being omitted from some codes.

Q:Faucet two hot and cold water hose aging, turn fixed, how to unload? I have removed the faucet from the basin, the leading hose

It seems that the faucet should also change even if you unloaded and installed will probably leak. There is a canned truffle.