Q:Im trying to replace my faucet sink in my bathroom the bolts wont come off ! I tried using the wrench I have but it wont turn what can I do? is there another tool I can use

The nuts that you need to remove are under the sink on the bottom of the faucet. Sometimes if they are corroded it's easier to undo the water lines and take the sink out and turn it over to get to them.

Q:New house decoration, why wash basin faucet water suddenly smaller, other leading normal?

There may be a filter plug you to remove the faucet to clean up or the angle valve did not open finished

Q:It slides around constantly. I can even lift it 3/4 inch upwards and see the pipes underneath in their little holes. I have felt under there with my fingers but I don't know what I'm feeling for to try and tighten it. What is the mechanism that tightens it to my sink, and how do I go about fixing it?

since your faucet has come loose to the point you can lift it, its not a matter of simply tightening the nuts. you will need to use plumbers putty to seal the deck of the faucet before tightening it down. if you skip this small step, you will have water infiltration into the cabinet. after resealing with putty, simply use a basin wrench and torque down the two plastic or brass metasl nuts. this shouild fix your issue

Q:Understand the water to the high reward

The center of the basin to the sides of the wall to leave a 550mm clearance size. The size of the toilet has a minimum of some control, the minimum width of 550mm, 600mm side of the toilet in order to save space to the toilet to narrow to 100mm or so, but even so, the wash basin is not only 300mm wide, must be highlighted Wash the table, it is not convenient to put things. Another key is to wash the center of the basin to the wall on both sides to leave a 550mm clearance size, that is to have 1100 of the net to put your desk, otherwise the use of bad and bad, so some Do not wash the table, it is necessary to a floor of the wash basin, put a soap what. But the more commonly used for a size of the basin: table 850mm, table basin: table 750mm, the size of the bathroom toilet is installed the standard size, but according to their actual situation, if the average height of the family are more High, then of course, is to design a little higher, if the average height of the home is not very high, then it is recommended to install the bathroom toilet lower.

Q:Open the faucet, the faucet and basin connection seepage, while the basin is also leaking under the water, leading off on nothing, what parts are broken? Thank you!

The faucet is broken, it may be on the faucet when the seal tape or gasket seal caused by lax, may also be broken.

Q:There is no way to directly from the basin leading to the water tank inside the bucket

From the outlet to install a three-way, the other tube to install the valve, I think you want to use water

Q:Bathroom faucet good? Or pull the faucet good?

If you do not have this habit, the general can be the faucet, because the pull-type life will be shorter, easy to bad.

Q:Why washbasin washbasin faucet is a shower that sprinkles the faucet on the faucet

Should not be good

Q:Yes I have all the proper tools, I'm using a basin wrench...I've got the old kitchen faucet disassembled...one retainer nut is off after some effort, but the other won't budge (white plastic style)...I can't get it off and it's the only thing holding me back from getting my new faucet in...this is suppose to be an easy project but it's killing my entire day, please help if you have advice!

If you are replacing the faucet, just break it off, even from the top. Throw it away. I ended up doing this after messing with the basin wrench for 30 mins. The sink is tough enough to hold up, the faucet components are often chromed plastic, which distort when you use a basin wrench anyhow. Use Teflon tape when you put your new faucet on to avoid this the next time.

Q:Which brand is good in basin basin faucet?

Which brand is good in basin basin faucet?