High Quality Rose Gold Plated Faucet

Ref Price:
$51.67 / pcs
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
50 Sets PCS
Supply Capability:
2000Sets Per Month PCS/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Description:
brass body
brass handle
brass cartridge
30CM 304 ss.flexible hose
brass parts
Rose gold Plated
Carton Packing Size:45*43*44.5cm
About product:
1.Competitive price, top quality due to we are the manufacture.
2.Sand die casting technology, the qualitiy can be controlled by ourselves.
3.Large-scale product line, more rapid delivery.

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Bathroom wash basin from the wall how many centimeters drainage pipe
The center of the basin to the sides of the wall to leave a 550mm clearance size. The size of the toilet has a minimum of some control, the minimum width of 550mm, 600mm side of the toilet in order to save space to the toilet to narrow to 100mm or so, but even so, the wash basin is not only 300mm wide, must be highlighted Wash the table, it is not convenient to put things. Another key is to wash the center of the basin to the wall on both sides to leave a 550mm clearance size, that is to have 1100 of the net to put your desk, otherwise the use of bad and bad, so some Do not wash the table, it is necessary to a floor of the wash basin, put a soap what. But the more commonly used for a size of the basin: table 850mm, table basin: table 750mm, the size of the bathroom toilet is installed the standard size, but according to their actual situation, if the average height of the family are more High, then of course, is to design a little higher, if the average height of the home is not very high, then it is recommended to install the bathroom toilet lower.
Q:Are bathroom faucets supposed to be positioned over the drain system ?
Most of the time they are; however, if it's not it should still drain properly. Sounds like you might have some sort of blockage in the drain, or that it's not venting properly.
Q:How do I stop my faucet from getting my counter wet?
You can replace the faucet with one that works better with your sink and doesn't cause the splash.
Q:The bathroom put a washing machine, bought a three-way dual-switch faucet
Oh, no worries! Because the current purchase of the toilet tank is just a high water design, so the water after the water tank will not return to the washing machine, and the main water pipe generally maintain 3 kg pressure, the toilet water tank in the water Water level, only the water will not return, tap water is a disinfection of sterile powder, you are not worried.
Q:Faucet switch and wash basin connection how to do leakage
Faucet and wash basin connection leakage is: tightening ring relaxation; or damage to the gasket;
Q:water is dripping out of the faucet at the same rate to fill a bath tub up to 6 high in basin in 8 hours?
This is extremely confusing
Q:My faucet is loose, and I dont know how to tighten it...?
Loose where? If it is loose at the sink, where the whole faucet moves, you must tighten it from under the sink and you will most likely need a basin wrench. Go to the local hardware store and discuss this with the folks there. They should be able to give some better advice as I cannot ask questions. They will sell you the basin wrench and explain it's use as needed. Good luck!
Q:With the basin under the basin to pay attention to what?
With the basin under the basin to pay attention to, taking into account the thickness of the basin, the mouth to be longer.
Q:Installing new faucet with sprayer into old basin?
The overflow is there so that if your kitchen sink clogs then it does not fill up your dishwasher with nasty sewer water. If you take the overflow (called an Air Gap) out then you would have dirty nasty water going into your dishwasher with your dishes. You can drill a hole in the sink but I warn you that this is difficult to do. I would recommend purchasing a pull out sprayer faucet. It's more costly but will save you the trouble of drilling a hole. They also make faucets that have the sprayer hole built in to the body of the faucet but this looks a little weird. If you get the pull out sprayer then you will like it and it looks nice too. So, just shell out a little more money and get a good faucet that looks good too!
Q:Plumbing Help, New Faucet install!!!?
You fit a 5/8 reducer down to 3/8th.
We are very popular with consummate skill, advanced workmanship, perfect after sales service in the world. From now on, our company devotes ourselves to enterprise construction and development, market is the guide, management is the basis, science is power.

1. Manufacturer Overview

Location Kaiping,Guangdong
Year Established 2004
Annual Output Value Above RMB5 Million
Main Markets
Europe and the United States, Australia

Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Guangzhou
Export Percentage
No.of Employees in Trade Department 4 People
Language Spoken: English;Chinese;
b)Factory Information  
Factory Size: Above 3000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Average