HG89 tube production line
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
I. Summary
The mill is intended for manufacturing round pipe of Φ32mm-Φ89mm with thickness of 1.5mm–4.5mm from cold-rolled and hot-rolled coil strip by means of unclosed tubular blank with its subsequent welding into tube, edge heating by means of solid state high-frequency welder, longitudinal seam welding in rolls of tube welding machine, cooling, further sizing or shaping and on-stream cutting of endless tube in measured lengths.
Finished product will be of round, square or rectangular pipe.
II. The technical flow of the production line
{SteelTape}→→ Double-head un-coiler →→Strip-head Cutter and welder→→
Spiral Accumulator→→Forming section(Flattening unit +Main driving unit +Forming unit +Guide unit +High frequency induction welding unit +squeeze roller)+ De-burr frame →→Cooling unit →→ Sizing unit and straightener →→Flying saw under computer-control →→ Run-out table
III. Basic conditions:
1. Round Pipe: 32-89mm
Pipe Thickness: 1.5 – 4.5mm
2. Square & Rectangle Pipe: 25X25mm –70X70mm
Pipe Thickness: 1.5 – 4.0mm
3. Pipe Length: 6.0m – 12.0m
4. Length Tolerance: 0-6mm
b) SteelTape Specification
1. Material: Carbon steel (δb≤500Mpa, δs≤235Mpa)
2. Steel Tape: Inner diameter: 470-510mm
Outer diameter: max=1500mm
Strip steel width: 100mm-280mm
Strip steel thickness: 1.5mm-4.5mm
The maximum weight: 4.0 tons
c) Electric installed capacity: appro. 600KW
d) Size of the whole line: appro. 70X6m
e) Line Speed: 20-70m/min
IV . Forming & sizing section
4.1 Forming mill gearbox, universal joint
4.1.1 Mill entry flattener by up-horizontal roll and below-horizontal roll, one positive five-roll flattener, one pair of feeding vertical roll.
4.1.2 Forming mill consists of:
- Driven stand: 7 sets (Horizontal)
- Driven stand shaft: Φ 90mm
- Material of shaft: 40Cr
- Side roll stand: 8 sets(Vertical)
- Side roll stand shaft: Φ50mm
- Material of shaft: 40Cr
- Gear box & universal joint: 7sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
- Main motor: 90kW Model: Z4-225-31 1 set
- Main redactor: 1 set
- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.
4.2 Sizing mill gear box, universal joint
4.2.1 Sizing mill consist of:
- Driven stand: 5 sets (Horizontal)
- Driven stand shaft: Φ 90mm
- Material of shaft: 40Cr
- Side roll stand: 5 sets (Vertical)
- Side roll stand shaft: Φ50mm
- Material of shaft: 40Cr
- Gear box & universal joint: 5 sets
- Material of gear box: cast steel
- Material of gear: 20CrMnTi
- Main motor: 75kW Model: Z4-225-11 1 set
- Main redactor: 1 set
- 4 sets single head Turk’s head, with 4 rollers*4sets
- One speed testing roller with air cylinder for CNC flying saw
- Horizontal roller frame with worm gear & shaft. adjust up and down at same time and level.
- Q:How does the pipe machine operate?
- The contents of the inspection requirements of the equipment required to fill in the site inspection records, a person in charge of the inspection and signature; for the discovery of equipment requirements in a timely manner reported, supervisors and workshop director to make comments, and report the results reported production
- Q:What is the difference between galvanized welded steel pipe and galvanized steel pipe?
- Galvanized welded steel pipe, galvanized pipe processing process is different.
- Q:What kind of plastic pipe is divided?
- There are thermoplastic PVC pipe, polyethylene pipe, polypropylene pipe, poly-formaldehyde pipe, ultra-high molecular weight polyethylene pipe; are thermosetting phenol plastic pipe.
- Q:Cement pipe machinery and equipment how to work?
- Rotate, then start the feeder from one end of the mold to the other end of the feed, when the concrete is higher than the mold ring 3-5mm, the concrete directly with the spindle contact, relying on the weight of the mold and the weight of concrete compaction reinforced concrete drainage pipe
- Q:The introduction of the pipe machine is
- Pipe machine is mainly used for the production of a variety of stainless steel decorative tube, such as: staircase handrail tube, anti-theft doors and windows with the tube, staircase handrail tube, fence, etc., can also produce a variety of car exhaust pipe,
- Q:What is the purpose of each mold of stainless steel pipe machine?
- Stainless steel tube molds use: not only can produce regular stainless steel tube, stainless steel square tube can also produce all kinds of special-shaped tube, such as plum tube, fan tube, oval tube and so on.
- Q:What is the stainless steel pipe machine?
- After molding can be polished or drawing, the end of the production process.
- Q:Pipe machine on the bearing what are the requirements
- A PLC programmable control technology, the whole process of automatic control to effectively avoid the factors that affect the impact.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
HG89 tube production line
- Loading Port:
- Tianjin
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- 10 sets set/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Hot Searches
Related keywords