Hand Stacker--WFH/SW

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 unit
Supply Capability:
1 unit/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

WFH
Hand Stacker
Disassembling and assembling is easy.
Can fit into smaller spaces when disassembled.
Equipped with wheels on the mast also allow it to be used as a trolley.
Light Alumium mast, easy for handling.
No any hydraulic problem, beasue it’s operated by winch.
The best brake function with special design is obvious.
Conforms to EN1757-1

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How do you remove the horizontal universal elevator milling cutter
Remove the milling cutter in a horizontal milling machine, and if you hammer it with a hammer, it is easy to break the knife and not be allowed to operate. The correct way to do this is to use both hands to pull the milling cutter out of the shaft, and when it's too tight, you can use a hammer to gently tap around the milling cutter.
Q:The tomb raider was not able to pry the gear in order
Press the switch and then descend the elevator down to the second floor and then climb to the right hand side of the cargo and pull down the first gear. Walk to the elevator and climb down the stairs to open the door between the second and third floors. Go up to the third floor and turn the elevator to the third floor. And then you go back to the second floor and you go to the third floor and you go to the sandwich and you get the second gear. Go up to the fourth floor and press the elevator up, go back to the third floor and switch to the three or four floors and twist the third gear. Come down to the entrance of the third floor elevator and then go in and use a shotgun to smash the three floors and the four floors. On the fourth floor elevator again back to the fourth floor, between the back to the fourth floor on the elevator by just open the channel on the wall opposite the detour to the fourth floor mezzanine dropped last gear lever.
Q:Introduction of vertical elevator milling machine
Milling machine is a kind of widely used universal CNC machine tools, can be processed on milling machine plane (horizontal, vertical plane) and groove (key, T slot, dovetail groove, etc.), the points of tooth parts (gear, spline shaft, wheel), helical surface (screw, screw groove) and various kinds of curved surface. In addition, it can also be used for the surface of the rotating body, the inner hole processing and the cutting. Hope to adopt!
Q:What kinds of tables are there? Which is better for the office?
In the office, see if you're new or in the office. New outfit can consider electric elevator table, common card position can buy lift platform. It is recommended that they have a variety of elevating products, including elevating tables and elevating tables.
Q:Can the stepping motor drive the hydraulic platform?
The hydraulic platform is driven by an oil cylinder, and the motor drive is a completely different way through mechanical means (screw, chain, gear, rack, etc.). In addition to mechanical means, depending on the power size, the step motor usually means that the equivalent power is not much, the maximum is a few hundred watts. The hydraulic platform is generally heavy, so it's unlikely. Or do you use a step motor to drive the hydraulic pump? It can, but also to consider the power problem, said earlier, smaller power stepping motor, if the original motor is a few kilowatts, certainly not.
Q:What is the main shaft of the horizontal milling machine
The CNC horizontal and vertical milling machine is a limited device to ensure the safety of machine tools and operating workers, and can also be used as multi-machine tool management. The CNC horizontal knee-type milling machine has perfect lubricating system, important driving parts and bearings have perfect lubricating equipment. Also have an indicator for frequent checks. The reliability is good, the economy is practical, the price function is better than the good.
Q:The characteristic of shear fork platform
Electrical control mode; Work platform form; Dynamic form; Walking actuators and so on. The correct choice of all kinds of configuration, the function of the lifting platform can be maximized, the best use effect is obtained.
Q:The structure of the universal elevator milling machine
The main shaft is used to install the tool pole and rotate the milling cutter. The main shaft is a hollow shaft with a 7:24 precision taper hole in the front, which is used to install the taper shank of the milling cutter. The longitudinal platform is carried by longitudinal screw, which is carried on the guide track of the turntable, and the workpiece on the surface of the table is moved vertically. The T groove on the surface of the table is used to install the fixture or workpiece.
Q:The principle of hydraulic platform is controlled by foot switch
Connected up button, hydraulic motor, discharge solenoid valve closed at this time, so the hydraulic oil cylinder filling to make uniform rise lifts, downward, control solenoid valve to open, due to the effect of gravity of the lifting platform, discharge of the hydraulic oil in the hydraulic cylinder, lifting table drop!
Q:What is the elevating platform for automatic mahjong machine?
This kind of failure, because after lifting motor flange loose inside the case, if there are no loose motor flange, it is lifting motor capacitor needs replacement, motor damage possibility is not big, most are motor capacitance shock wear caused by the inability to fail, knowing all think will be the motor is broken

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range