dismantling joint-epoxy coating

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

PN from PN2.5to PN60
Material as Ductile iron, WCB,SS etc.

1.Material:Ductile iron, WCB, SS etc,


2.Size:from DN100 to DN2200


3.PressureZ:from PN10 to PN40


4.Sealing:NBR,EPDM,PTFE,Graphite


5.Coating:epoxy painting,fusion bonded epoxy,thermal spray metal



Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to inspect ductile iron pipe fittings?
On the quality of single pipe can analyze it from the surface is sand type and water cooled pipes, K8 pipe is different from Shanxi root nature is that the proportion of grade K9 cement and cast iron pipe and the K8 pipe are different, there is no national standard and non standard, no K8 tube, only is the production plant in order to obtain more profits, the dealer is not up to the national standard K9 grade pipe called K8 grade ductile pipe, K9 pipe cement weighs about 1/5 weight of the pipe, but is played in the role of anti-corrosion,
Q:Could you tell me how to weld ductile iron parts and steel tubes?
MG289 electrode can be selected, welding electrodes and ductile iron into eighty degrees around the pipe around OK, and the intensity is higher than the strength of the cast iron. Direct cold, no heat treatment after welding.
Q:How is the weight of nodular cast iron pipe calculated?
In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%.
Q:How can ductile iron pipes be connected to steel tubes?
But pay attention, because ductile iron pipe material is crisp, and the two connecting flange sealing surface is best all the plane, in order to prevent the uneven force and damage to cast iron flange.
Q:How much is the installation of a two degree elbow for ductile iron pipe fittings at 11.25 degrees?
The main components of ductile iron pipes are carbon, silicon, manganese, sulfur, phosphorus and magnesium. In the ferrite and pearlite matrix on the distribution of a certain number of spheroidal graphite, according to the nominal diameter and the elongation of different microstructure of ferrite and pearlite in different proportions of small caliber pearlite percentage is generally not more than 20%, large diameter of the general control in about 25%. Minimum tensile strength: 420/Mpa, minimum yield strength 300/Mpa, minimum elongation 7%.
Q:Comparison of C and K grades of ductile iron pipes
The nominal pressure ratio of the C class pipe is lower than that of the K grade tube, and the applied pressure is low.
Q:What are the categories of ductile iron pipe fittings?
Can be divided into injection molding, plastic pipe fittings three and rotational molding. Two kinds of popular method is plastic or plastic. They are sometimes referred to as lining plastic pipes.
Q:How can the ductile iron pipe be connected to the PE pipe?
Cast iron pipe and PE pipe is connected with a lot of what is the most secure connection, flange connection (PE flange head + anticorrosive steel flanges + rubber gasket).
Q:Is the cast iron tube the same as the ductile iron pipe?
According to its manufacturing methods can be divided into: sand, centrifugal pipe, straight pipe, continuous cast iron pipe and sand pipe.According to the material used, it can be divided into gray iron pipe, nodular cast iron pipe and high silicon iron pipe.
Q:How to improve the quality of nodular cast iron pipe fittings
When the molten iron temperature is too low and the inner wall temperature of the tube is low, heavy skin defects will occur. When the molten iron temperature is high and the molten iron gas increases, porosity defects can be generated. In the medium frequency furnace, the hot metal should be provided according to the process specification, and the temperature of the inlet and outlet and the cooling rate can be controlled reasonably in the process of production.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range