DIN3353 F4 DCI non-resilient Ductile Iron Gate Valve

Ref Price:
Loading Port:
China main port
Payment Terms:
TT OR LC
Min Order Qty:
5 set
Supply Capability:
500 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

1.General design:DIN,BS,ANSI
2.Rising or Non-rising stem
3.Solid wedge disc
4.Clockwise closing direction
5.Bolt bonnet

Product Name:

gate valve

 

Technical Data

DN40-DN2000mm

Body: Cast Iron, Ductile Iron

Stem: Stainless Steel,Brass

Disc: Ductile Iron

Flange Connection:EN1092-2 PN10/PN16/PN25,

                             ANSI B16.1

                             BS10 Table D/E,JIS10K/16K

Standard:DIN3352-F4/F5,BS5163,BS5150,BS3464,ANSI

 

Product Features

Bolt Bonnet

Replaceable O-ring

Low torque operation    

Outside screw and yoke

Clockwise closing direction

Graphite packing

Seat rings are pressed into wedge and body.

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Faucet water is very small, a little blocked, how to do
It is easy to disassemble the faucet and take it out
Q:Line cut ruby taps how to calculate the guide wheel distance
The amount of distance between two ruby taps
Q:How to connect the water heater to the basin
With a hose connected to the embedded hot water pipe and wash basin on the hot water faucet entrance, and then wash basin on the cold water inlet access to tap water. So open the faucet can flow out of hot water, and can adjust the water temperature.
Q:Faucet nozzle more water or directly open water
Not necessarily the general faucet is now with a bubbler, limited to Ji Han irrigation pit thieves ghost daughter-in-law, the control of water flow and the nozzle structure will also affect the flow
Q:How to repair the faucet handle?
The kind of cross screw on the handle is good to get, as long as the screw did not slip teeth. You go to find a thick metal, the front part of the plane to make a screw can go into the hole, fixed with a vise clamped. The rear folder, plus a heat shrink tube sets, after heating is not a hand.
Q:Wash basin faucet how to change the hose
First, remove the whole copper fixed base. Second, the nut from the threaded tube counterclockwise rotation down. Three, hose worn yellow wrench, nut, thread tube, silicone pad. Four, between the hose through the need to install the vessel (sink, basin, etc.). Note: the silicone pad in the vessel on both sides of the installation of a piece, and finally tighten the fixation can be more stable. 5, the hose of the small head, hand screw into the faucet, screwed to the screw can not move, without the help of other tools to die.
Q:What are the models of faucet specifications? How to identify the faucet is good or bad?
The standard washbasin's mouthpiece is the M24 specification. The faucet of the dish is M22, and the connector is not the same. Non-standard products on the free.
Q:Heating faucet single switch and double switch which is good
Heating faucet single switch and double switch which is good
Q:I am getting pebbles clogging up the cold water side of my bathroom faucet, whats up with that?
you may be getting limescale, that will form stones, but its unusual. You will need a water softener if this is the answer. Try crushing one, it should be fairly soft
Q:Is Brasso good for shining up some "brass" basin faucets?
if you aren't sure if it actually is brass i'm not sure how well of a job it will do in polishing it. Basically most polishes work by rubbing off the oxide that has formed. I'm not sure how brasso wil react with non-brass metals, the same way iwouldn't polish sterling silver with brasso. if anything might i suggest some sort of home concoction? I Think vinegar was something peoples used as polishing. It has an acidic property to help remove the oxide, but no chemicals to worry about that might mingle with the metal. I don't recall what else they mix with the vinegar. You can just google "home made polish" I'm sure it'llg ive you a list of them Well good luck with your fixtures.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range