*G1/2''inlet ,16mm outlet
*Urinal Flush Valve, Button Type Urine Flush Valve, Urinal Flusher
*Working Pressure: 0.1-0.8MPA
2) International Quality Award Certificate approved by CELAB Italy, EN 12541:2002
Repair and Maintenance
Our valves shoud be cleaned and maintained regularly according to the water environment and water quality (usually one year or half year)
Stop supplying water, unscrew the cover of the main body with a spanner and hitch the floating valve
Clean the strainer and rubber seals of the floating valve,then stab the Mud-stopping slot with steel wire less than 0.4mm .Make sure the slot has no sundries
Clean the silt and flaxsilk in the “V” of the rubber ring inside the floating valve,make sure the sealing performance during working
4. Fit those parts back to their place and buck-up the cover,make sure there is no seepage before you use it again.
- Q:Toilet squatting tank flushing or good flush valve
- The advantage of the flush tank is to be able to water, the pressure on the water pipe is not demanding, the disadvantage is that the volume is big. The flush valve instead. If your home water pressure is high, do not often stop the water, then install the flush valve better, and vice versa on the water tank it.
- Q:Flush valve and triangular valve use and function
- Is the role of the switch, if the leading water leakage and other phenomena, may turn off the triangular valve, do not have to worry about the total valve in the home.
- Q:Old delay flushing valve does not delay how to do
- It may be four bad, you can go to after-sales maintenance of the
- Q:How to do the flushing valve leaks
- Flush valve works: When the water from the inlet into the water tank, the drain is pressed by the rubber film, can not drain. As the water level rises, water flows through the hole A through the hole and flows from the hole B into the elbow. As the rubber membrane is equal to the upper and lower water pressure, still hold the drain. When the water level continues to rise above the highest point of the elbow, the water will flow through the pipe into the drain. As the hole B is greater than the hole A, the water through the A hole when it is subject to greater resistance, pressure is also lost, so the ball within the crown to reduce the amount of water will appear at the top. At the same time, the upper pressure of the rubber membrane is drastically reduced, and the lower pressure is equal to the pressure of the atmospheric pressure plus the pressure generated by the water. It is much larger than the upper pressure, the rubber film is protruded and the drain is opened, and the water in the tank is discharged rapidly (about 10 seconds). When the water level in the tank drops, the water in the ball crown can still be discharged through the elbow due to the siphon phenomenon, keeping the vacuum present, so that the rubber film will not move down. When the water in the box is finished, the rubber film rubber mold is pressed again Drain, re-water storage. If the water flow in the inlet is controlled, the drainage cycle can be determined. So the cycle, so that the toilet can be automatic, regular rinse. This is the working principle of the toilet flushing valve.
- Q:Hand operated toilet flush valve works
- Different places of the toilet with the flush valve is different, there are induction, pedal, manual three toilet flush valve, there is a water tank is a toilet flushing, the principle of their flush valve are Different. Public toilet is a relatively large flow of people, it should first consider the conservation of water, followed by the use of large flow of water, the impact of a one-time washed dirty things, it is the principle of the use of the bucket placed in the height, the use of water potential To work.
- Q:Flush toilet flushing valve is broken
- Support your ideas, I changed for several times, it is very simple you go to the hardware store to buy new sanitary ware back (generally have to sell) back after I do a successful practice try to see buddy
- Q:What valve is the flush valve?
- Side of the special valve.
- Q:Whether the flush valve is a good hand or a good hand.
- Flush valve hand press, the water quickly, large water. Hand twist the water is not too big. To say that kind of good, but also to see where used?
- Q:Bathroom flush valve problems, how to repair the water has been
- Open the cover to see the drainage components have two under pressure button, because the reasons for water quality or lubrication, the bomb is not up. Give you two kinds of solutions.
- Q:Is the size of the flush delay valve for the toilet uniform?
- First of all, we can see the home then flush valve inlet of the inner wire connector is how large size (please note that the size of the water pipe), if it is PPR wire connector, each connector will be marked above, such as 25 × 3/4; × 1 These words, before and after the numbers such as 25,32 refers to the size of the PPR tube, followed by the number such as 3 / 4,1 refers to the size of the inner wire connector, 3/4 is three quarters of three inches, 6 points ", then DN20 flush valve connector; 1 is an inch, jargon" 1 inch ", then DN25 flush valve connector
After years' hard work and development, now our company becomes one of the leading enterprises in the field of faucets, toilet sets and shower products production and sales.We always keeps "Based on People, Winning for Quality" as our sales motto. We look forward to receiving your detailed correspondence in the near future.
1. Manufacturer Overview
|Annual Output Value
||US$50 Million - US$100 Million
||30.00% South America
30.00% North America
5.00% Eastern Europe
2.00% South Asia
2.00% Southern Europe
2.00% Northern Europe
2.00% Central America
2.00% Western Europe
2.00% Eastern Asia
2.00% Mid East
1.00% Southeast Asia
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||51% - 60%
|No.of Employees in Trade Department
||30,000-50,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range