1.Each RGB 5050 LED has a IC(WS2811) inserted in it.
2.Each LED on the led strip can be cut and controlled seperately.
3.Can design every kinds of lighting effect or even animation as you want
4.With a high grey levels.
5.60 or 30 leds/m, Each LED and one IC as one unit can be cuttable.
6.Gray level 256
each 1 LED unit
each 1 LED unit
Control IC Type
Customize your strip light by picture or by technical datas.
Other products in our campany:
LED panel lights
LED module special for lightbox
Parylene coated IP66 LED strip
Packing & Delivery
plastic bag intside, cartons outside
Estimated Delivery Time
2-8 business days
3-8 business days
2-10 business days
1-7 business days
6-14 business days
7-12 business days
China Post Air Mail
7-15 business days
China Post SAL
14-30 business days
3-10 business days
30-40 business days
1. 3-5 business days for Sample Orders; 7-30 business days for Bulk Orders for Bulk Orders.
2. "Business days" means Monday-Friday, excluding holidays.
3. DHL and UPS cannot ship to military or P.O. boxes address
4. The Shipping Service above is for reference only, for any other questions, please feel free to contact us.
Send a message to us:
Q:LED current increases beyond 20MA, or when 30MA-50MA has consequences for LED lights?
The high power LED does not matter, but the straw hat, like 5mm small LED lamp is fatal, usually these small LED rated current is 20mA, a do make it work on the 15--18ma, you need to 30MA-50MA, it is early light oh, quickly over the
Q:PCV flame retardant material toxic? (LED background light band)
This band of material itself is made of rubber, and all the glue is with formaldehyde, want to go to formaldehyde, there are two ways, one is to buy. Activated carbon sucked, and the two is the doors and windows open, so that the room ventilation.
Q:Led how to connect the light belt?
Look, are you using a high voltage light belt or a low voltage light belt?! The high voltage is connected directly to the 220V power supply by the plug, but the low voltage light belt needs to be equipped with a transformer and the switching voltage is attached to the light belt. If you don't understand Baidu HI, I'll answer it for you at any time!
Q:What's the brightness of the LED light band? Can I use it for lighting?
No, the light belt is auxiliary lighting. Mainly to create a spatial atmosphere.
Q:How can I arrange the lamp belt in the wardrobe?
When making a wardrobe, take a good line, drill a hole, wire to the wardrobe inside, and then install a micro switch, turn off the lights, open the door, light
Q:Can anyone tell me what's the difference between LED lights and indoor and outdoor installations?
Outdoor installation: outdoor installation because will withstand the wind and rain, if the use of fixed 3M glue, a long time will cause the decrease of the 3M adhesive LED lights off, so often used for outdoor installation fixed card slot, need to cut and connected and installed in the same place, method, just need another with waterproof glue, waterproof effect to consolidate the connection point.
Q:Does the LED low voltage lamp belt belong to the luminaire?
Does not belong to decorative lighting products. Lamps and lanterns, in fact, refers to the lighting products that have changed the light distribution. LED bulbs are not light fixtures according to laws and regulations. They are listed as light sources.
Q:Why does the length of the LED band fade with length?
This doesn't matter where the power is put. Now that the lights are in parallel, the male Street meets up. Too many connections cause excessive power load.
Q:Which is better, low voltage LED belt and high voltage LED lamp?
If the application can be any contact in the clothes cupboard, jewelry counters, kitchen cabinets and so on places where children, for security reasons, the best choice for low pressure led lights, in addition, low voltage lamp with life in general than the high pressure lamp with high 10000 to 20000 hours, please according to the actual demand, choose a suitable for your lights, recommended to choose low voltage lamp with photon LED lighting, the quality is very good, even if the leakage is not in any danger.
Because of your LED light line, the switch control (off) is zero line. You might as well see if there are any other fluorescent lights or LED lights off at home. If there is, the bus FireWire and zero line exchange, and if only this one, then the LED lights line for FireWire and zero line swap, this phenomenon will disappear.