LED TUBE LIGHT 18W 120CM RA>70 PF 0.6 AC180-265V INPUT VOLTAGE 1600LM GLASS MATERIAL SPECIAL OFFER
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
LED Tube Light are receiving global recognition for their energy saving capabilities, long service life ,easy installation and the ability to reduce carbon emissions across a host of different sectors.
Specifications of LED Tube Light Voltage:AC85-265V 50/60HZ 18W 120CM Beam Angle:300 degree
LifeSpan :30,000 Hours
2-3 years warranty
CRI :RA>70,RA>80
CCT;3000-3500K,4000-4500K,6000-6500K
Features of LED Tube Light
The LED Tube Light is widely used and are designed and manufactured to replace the traditional grille fixture ,CFL tubes , the superior SMD LED solution and purity Glass material makes the luminous efficacy high to 100LM/W, it is of excellently heat managed by conjoint structure which maintains the LED working temperature in a comfortable condition.
Excellent Heat Sink
SMD LED solutions
Superior High Quality
Eco-friendly
Energy Saving Perfect Replacement for All Lamp
Blast Free, Starter Free
Applications for LED Tube Light
Replacement CFL for traditional lamp, such as store, supermarket, commerical builing and anywhere
- Q:Xinda is a popular led lighting tube
- Take LED lamp tube, seek the big and bright illume directly, price is certain preferential.I hope my answer will work for you.
- Q:Fluorescent fluorescent lamp tube can replace led fluorescent lamp tube?
- The original circuit was an alternating current that was attached to the ballast, and the ballast two to the two sides of the fluorescent lamp; To install led fluorescent lights, remove the ballast directly, and the positive and negative poles of the exchange are connected to the two sides of the led fluorescent lamp.
- Q:Use LED fluorescent lamp tube to replace, the line of original daylight-tube seat should be refitted
- If both ends with electronic ballast, it is necessary to put the two end of the circuit board uninstalled, two card old fluorescent lamp line sub respectively, and then to the outside power, install the LED fluorescent lamp with respect to OK.
- Q:How do you make the led lights like fluorescent lamps
- According to your requirements, you need to find a special manufacturer. At present you can only buy an LED light. The voltage depends on how many leds. You can't do it with a battery.
- Q:How to drive LED fluorescent tube with electronic ballast
- First, remove the sun tube and the starter. Second, then replace the LED fluorescent tube, which can be used directly. 3. Inductance ballasts can not make any changes, but the electronic ballast will all wire cut, remove the electronic ballast, the zero line and the line of fire respectively from the two ends of the lamp holder.
- Q:Fluorescent lamp double lamp tube wiring method
- Leds that do not normally require special orders are mostly built with built-in power, which is directly available. Most can only need to remove the starter on the traditional stent line (is a cylinder bracket highlighted below) mount tubes can be used, if not yet so could you use the stent is a relatively new "electronic" will be a little trouble need you open the stents to get inside the ballast also take off to the inside of the line directly connected to the utility, LED bulb is directly at the mains. Of course, if you understand the circuit and you're not afraid of trouble, it's advisable to remove the "regenerator", because the "ballast" is a power drain.
- Q:Electronic ballast tube lamp change led lamp tube how to change circuit how to do
- Usually direct 220V, in the package of the lamp tube has the wiring diagram, does not use the original ballast, the nature is different
- Q:How to meet? The rectifier is very easy to connect
- Went on two of the ballast with black and white and two sets of lines, a set of a tube, the last wire connects ballast is ok, if the change over time, to check whether a set of ballast to replace, so consider in ballast, if only a single change, that is about to change the bulb.
- Q:What installation is the T8 LED tube?
- Installation instructions 1, inductance magnetic ballast installation: Turn off the power switch. Remove the fluorescent lamp, the regenerator, and short-circuit the ballast. Install the LED lamp on the lampstand, insert the G13 lamp holder and rotate the LED lamp to make it permanent, LED out facing down. Turn on the power switch.
- Q:The output of the led lamp is low
- This should be unsegregated, and the output should be around 75v.He is unsegregated, and the output voltage is high if there is no load.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
LED TUBE LIGHT 18W 120CM RA>70 PF 0.6 AC180-265V INPUT VOLTAGE 1600LM GLASS MATERIAL SPECIAL OFFER
- Loading Port:
- ShangHai
- Payment Terms:
- TT ,LC AT SIGHT
- Min Order Qty:
- 10000 pc
- Supply Capability:
- 100000 Pcs Per Month pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords