Q:What can cause double adhesive to lose stickiness?

Toluene, xylene, tetrahydrofuran and other solvents, I do not recommend you to use, because they are mostly toxic, but also polycarbonate, PC/ABS and other notebook shell commonly used materials swelling.Finally, there is a trick, some adhesives at low temperatures will lose viscosity, with waterproof bag, put into the refrigerator freezer, cooling to about -20 degrees, take out pry...... I wonder if it is possible. (the glass temperature of some functional components of the adhesive is below -50 degrees, this method is not applicable).Heating also allows adhesive viscosity to decrease and strength to decrease and thus may be separated

Q:How do you remove the foam glue on the wooden floor?

1, with a hair dryer to the double-sided adhesive residual floor, blow a pass, to be weak after heating double-sided adhesive can be torn out, gently.2, anhydrous alcohol rub division, if the home has anhydrous alcohol, you can find cotton balls dipped in some anhydrous alcohol, to erase traces of double-sided adhesive. If there is no absolute alcohol, the white oil at home can also be replaced.

Q:What are the 3M double-sided adhesive?

No substrate material, double sided adhesive (directly coated with acrylic acid): such as 3M467, 3M468, 3M9473, etc.;PET base material double sided adhesive (made from PET base material, double sided coating acrylic acid glue): such as 3M9495MP, 3M9795B, 3M9495LE and so on

Q:How do you apply double-sided adhesive tape?

4. The joint of the double adhesive tape should be staggered with the joint of the plate;5, with adhesive tape, it is best to use rubber scraper, in a parallel sweep way, the tape evenly affixed to the roller, in the tape and the roller can not leave the bubble; (if the bubble retained, the application needle punctured)6, in determining the location of the printing plate, should avoid the printing plate and tape premature contact, to determine the printing position, remove the tape protection layer, the plate with rubber roll, in parallel with the way on the adhesive tape;

Q:What type of tape do you use for paint marking test?

8, 3M water labeling labels warranty and safety tape: 3M5557,3M5557NP, 3M5558,3M55599, 3M metal foil tape: 300PL, 508SN10, 3M grounding heat sink adhesive film: 737311, 3M conductive copper foil tape: 3M118111821183119411881189124513452245324512, 3M conductive aluminum foil tape: 3M112011701172117811791267, AL-25BT, AL-50BT, AL-25DC, CEA-1, CEA-213, 3M electromagnetic wave absorbing materials: 3M, AB2000, AB5000, AB6000, AB7000

Q:High temperature tape can not be stripped off after high temperature?

Low VOC tape, VHB tape, acrylic foam tape, double-sided tape, OCA optical AB double-sided tape, LOCA liquid optical adhesive; thin waterproof tape, removable double-sided tape, super sticky tape; peeling, no traces of the hook tape. All kinds of tape personalized research and development, custom-made and die-cutting processing.

Q:The advantages and disadvantages of the mesh double sided adhesive tape, and the influence of the density of the mesh on the adhesive tape.

What material should be divided into mesh adhesive tape, the substrate is different, advantages and disadvantages are different, the main use is also different.

Q:PET what's the advantage of double-sided adhesive?

I wonder if you are using this piece of industrial processing. If so, you can check it with Baidu

Q:With scissors to cut the foam double-sided tape, the scissors left a foam glue, sticky extra strong, difficult to remove, what is the way to remove the residual foam on the scissors?

First, use wire ballTools / raw materials: steel wire balls (for washing dishes, washing dishes) and dishwashing detergent.Methods / steps:1. Bring out the scissors glued to the glue, dip the water into the wet scissors, and apply the detergent;2. Brush with steel wire brush;3, clean water on a clean.

Q:Will double face adhesive affect its stickiness in summer?

Check whether the edges of the double adhesive tape are adhered or not, and whether or not the bottom sheet is leaking of siliconDouble adhesive tape edge adhesion or some parts of the bottom sheet leakage of silicone oil, in the processing process will cause waste paper rupture, can not be normal production. Therefore, before processing, take a length of about 1 meters of self-adhesive materials, hand peeling, to see whether the edge or other parts of the smooth, uniform peeling of the parts. Usually, paper and paper edge bottom adhesion occurred in a roll coating adhesive material cutting volume, and generally occurs only in the outer layer of 7 meters to 10 meters, so the drum encountered double-sided tape cutting edge with adhesion, don't immediately assert that the whole roll of paper have this problem.Also note that stripping light weight tissues (such as 60g/m2 and 80g/m2 facial tissue) is more powerful than peeling off heavy paper, and the lighter the paper, the more tightly it feels. Because of this, sometimes, according to the customer's request to cut the shape of the customer's choice of double-sided tape, can not be completed at the regular processing speed.