Used for air-conditioner
Component brands can be AMP, JST and Molex
UL-, CSA-, CCC- or VDE-approved
Customized packing types are accepted
1.This product exported Mexico, the United States, Poland,Canada,England,and other countries.
2.We guarantee each product will be checked.
3.If there are bad products, we will promptly pay compensation to customers without any charge.
4. We also sell a lot of similar electronic products, varieties, good quality.
- Q:Why this cable has not yet been certified
- Electromechanical products are usually used to be assembled into parts, multiple parts and then assembled into a single product, the number of products or the number of pieces measured
- Q:What is the difference between "wire" and "cable"?
- Simple point, the plotter is generally used to out of the line map, the general is the Academy of Engineering, the Bureau of the use of a CAD map, and some can also be some effect of the general effect of the map, generally suitable for color requirements are not very high, but right Print accuracy requires a high place. Inkjet machine can be divided into indoor and outdoor ink, outdoor irritating smell, for outdoor advertising like the effect of the map, the indoor no irritating smell, the general subway, as well as other indoor advertising are used this out of
- Q:Fiber optic cable split box, integrated wiring box, cable terminal box, cable transfer box difference
- KVV is the control cable, generally do industrial control; and RVS is twisted pair, generally used for weak system, to eliminate the interference requirements of the occasion, such as two-wire bus system, specifically, the electrical fire bus more Such as RS485 bus and so on.
- Q:Wire pipe inlet air switch trip how to do?
- Wire pipe water problem: In fact, this problem is very serious, then this line should be scrapped or replaced, if you continue to reluctantly use not only to bring you the safety of trouble and the insulation of the wire dropped sharply! Because there is water it will lead to internal leakage can also make the wire heat caused by wire burning and trivial trivial accident, so be sure to take the necessary replacement! Supplement: the wire out of all, with the wire to grab the absorbent gauze and the like back to the twitching, many times for the gauze to dry the water, hair dryer toward the tube to heat the tube to dry and then re-layout of the new line.
- Q:Help look at such a configuration will not have compatibility issues! Do you need to improve? Budget in 5500 or so
- This situation generally have to extend the line triangle can link the ground, the two feet when you use the foot to feel the foot, and step on the bench as long as the non-conductive feel. No seriousness
- Q:Seeking the basement of the outer wall piercing the cable after the casing, how to solve the water (200 points online)
- To be considered is the Great Wall power line is not long enough, the power is not big enough to see the power on the label, if the 12V to 15A or more I think will be more stable, my Dell machine power cord surprisingly short, but also To buy the extension line again.
- Q:Now the market professional installation monitoring the construction team how much money a point? , As well as cable patch panels and telephone patch panels how much money a point? Is it distance?
- Directly to find Dell customer service bar, the general warranty period are free replacement, unless the insurance of the. You can extend the warranty period, it seems you like to do the experiment.
- Q:Ipad charging display does not support this accessory
- The problem lies in the charger between the machine, IPAD charging is to a charging protocol to complete, when the IPAD did not receive the agreement signal will be prompted: do not support this accessory, Apple's products have charging protocol, charging Is through the data line in the two lines and IPAD transmission charging protocol signal when ipad received the charging protocol signal after the machine internal charging circuit began to open the internal charging circuit to charge, the problem is to accept the charge signal is not so prompted not to Support, change the line to try
- Q:Where should the inner diameter of the plastic tube of the cable be at least the number of times the outer diameter of the cable?
- You are not very clear: how to start again? 300μF capacitor is normal? If the sound is normal (very small) after no-load start, the cable and the motor temperature are normal, the coil can be judged to be normal
- Q:What is the cable for rvv? Is it a power cable or a control cable? What is the cable?
- The installation process is a certain requirement, high and low voltage cable bridge should be installed separately as usual, a wall laying vertical pipeline (slot) or installation equipment, the power distribution between the depth of D1 = 1200 ~ 1500mm; weak Between the deep distance from the D2 = 1100 ~ 1400mm more reasonable. The length L1 and L2 between the power distribution and the weak can be determined according to how much electrical equipment and pipelines (slots) are installed in the room. "Civil building electrical design specifications" proposed "shaft size in addition to meet the wiring spacing and terminal box, distribution box layout must be the size, but also in the box before the left not less than 0.8m operation, maintenance distance" requirements. In the weak equipment, the operation and maintenance distance is not specified in the provisions of the Code for Electrical Design of Civil Buildings, but it should not be less than 0.8m. Cable to wear steel pipe wiring, should be reserved in the floor steel pipe, wiring should be completed after the plug fire fire blocking material. Cable bridge installation should be horizontal, the maximum sag should not be greater than 10 mm; proposed separate installation
We are implementing mature quality control systems and make sure our products are perfectly qualified. Our company always maintains "Improving quality, Reducing cost, Continuing improvement and Satisfying customers' needs" as our quality policy. We aim at saving your time and money by providing a single source for the entire cable areas.
1. Manufacturer Overview
|Annual Output Value
||US$10 Million - US$50 Million
||ISO 9001:2000;ISO 14001:2004;ISO/TS 16949
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||31% - 40%
|No.of Employees in Trade Department
||3,000-5,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range
||Low and/or Average