Lift Rated Capacity
Platform Extend Capacity
Wind speed 45km/h
Max. Machine Height
Max. Platform Height
Platform Extend Length
Hydraulic oil box
-Can bus line intelligent controller
-Automatic pot hole protection system
-Electric circuit fault code display
-Rotary strobe light
-Euro Ⅲ emission standard engine
-Hydraulic electric welding machine
-Hydraulic air compressor
-Hydraulic high pressure water pump
-Hydraulic oil radiator
-AC power source connected to platform
The product is mainly applied in the fixing, constructing, detecting and maintenance of large-scale bridge, steel structure workshop and sorts of aerial equipment. It can be used in all kinds of rugged terrain. CE certified.
1)Structure: scissors, enable extended-platform, good performance of elevating and loading.
2)Sole control system, drive mode: 4×4, maximum speed：6.5km/h.
4)Tilt alarm, the auto-leveling system of four crutch-leg .
5)Emergency down-valve device.
6)Double anti-press protection: electric-control and safety-web.
- Q:Introduction of vertical elevator milling machine
- XD5032 X: milling word pinyin initials, on behalf of the milling machine D: should be on behalf of the manufacturer, 50: dalian is 32: vertical lifting platform structure is the most giant slalom spindle diameter of 320 mm
- Q:How do you remove the horizontal universal elevator milling cutter
- Tie rod and the threaded part of the milling cutter is too short, removing cutter bar back a loose, threaded connections even fewer number of buttons, easily when tapping threads dozen hair, and make the cutter not screw down, or make the damage of tie rod.
- Q:How does the elevator repair
- All parts should be filled with lubricating oil to extend the life of the bearing. The oil and oil level of hydraulic oil. The platform rises all the way up, and in this position, the hydraulic pressure should be 40 to 50 mm above the bottom of the box. Hydraulic oil is a variation of dark, sticky or grit, such as a discovery should be replaced in time (32 # hydraulic oil) Annual maintenance A. check all the hydraulic pipes and connectors. The pipe shall not be broken, the joints shall not be loose, and all the joints must be tightened. Remove and disassemble the descending valve, blow the plunger through compressed air, then load and resettle. C. the elevator hydraulic oil is put in the rejected, tighten the joint remove oil filter, after cleaning, use compressed air is clean, and then back into the tank, and the connecting line. (put on new oil and don't keep using the old oil. Otherwise, the moving parts in the system will accelerate the wear and tear.)
- Q:What about the platform of southworth?
- As far as I know, at present in domestic, the lifting platform with voss is still a better public praise manufacturers, has a manufacturing license certificate and installation license certificate, old brand, trusted. Businesses are now registered in Shanghai and manufacturing plants in Shanghai.
- Q:The tomb raider was not able to pry the gear in order
- There are four of them, four of them. See the white climbing wall outside the elevator? Find a way to burst open a hole in the iron wire and climb to the fourth gear. There was no order in this gear, four of them were done, and the elevator fell down.
- Q:The purpose of the rail elevator
- The product structure is strong, the load is large, the lift is stable, the installation maintenance is simple and convenient, is the economical and practical low floor space to replace the elevator's ideal cargo transport equipment. According to the installation environment and use requirements of lifting platform, choose different optional configuration, can achieve better effect, the use of this product is mainly used in chemical, high temperature and high pressure, power plant, the nuclear industry base, such as explosive explosion protection enterprise.
- Q:The home is decorated, make a tatami mat the platform should pay attention to what aspect?
- The first is the choice of control. Usually tatami lifting column control mode are: pure manual type, electric type, manual and electric integration and so on three kinds of control modes, the future there will be mobile intelligent control. The pure manual type, which is to turn the crank, makes the lifting platform up and down. The advantage of this type of control is that even a blackout does not affect the use of the product. The disadvantage is that manual control is time-consuming and time-consuming.
- Q:The hydraulic platform is compared with the normal lift platform
- Double protected leg structure, work safer, and can be close to the working face lift. The machine is the answer for you!!
- Q:How does the platform maintain
- Remove and disassemble the valve, and remove the valve core and remove it from the new installation. Put all the hydraulic oil in the tank into the tank, remove the oil absorbent filter, and put it back in the tank. The oil tank refilled with new oil.
- Q:How does the table in the middle of the tatami mat go up and down
- Tatami lifting table, still have certain technical content of the installation, general to famous tatami custom manufacturers (such as: appropriate PiaoSen furniture customization) give you installed! If it's not installed, it's usually a small workshop, and it's recommended that you find a professional to install it
1. Manufacturer Overview
|Annual Output Value
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
|No.of Employees in Trade Department
|No. of Production Lines
|Product Price Range