LED SMD 3528 Red Light

Ref Price:
$0.02 / pc
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
5000 Pcs pc
Supply Capability:
10000000 Pcs Per Month pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

LED SMD 3528 Red Light Regular color temperature:


warm white 2600-2900K,2900-3200K,3000-3500K
natural white 4000-4500K,4500-5000K
cool white 5000-5500K,5500-6000K,6500-7000K
cold white 7000-9000K,9000-15000K

Available SMD type:
3528, 2835, 5050, 5730, 3044

Stable quality w0, 5730, 3030

Stable quality with low optical attenuation

1000h<1%, 3000h<3%, 10000h<8%


A. Meet CE, FCC, RoHS, EMC,LVD certification;

B. No RF interference, no buzzing noise and no UV radiation;

C. Low power consumption, high intensity low lumen attenuation and wide range of available operating voltage;

D. Easy to install and maintain,replacement of traditional bulbs;

E. Environment-friendly, No hazard of mercury or lead entering the environment.

F. High efficiency and energy-saving compared to conventional fluorescents which are equal bright, an

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Welding method and notice of SMT LED
I recommend reflow soldering under normal conditions and manual welding only when repaired. 2 manual soldering electric soldering iron maximum power can not exceed 30W, welding temperature is controlled within 300 degrees, welding time less than 3 seconds. 3 do not touch the colloidal iron welding head. 4 when the pin is heated to 85 degrees centigrade or higher than this temperature, it can not be pressed. Otherwise, the welding will be broken.
Q:What is the principle used in SMD LED lamp, should pay attention to what the problem?
LED white is the light emitting diode, a PN junction to the most important use of SMD beads is the heat, according to the different manufacturer beads, glue package is not the same, should pay attention to pre baking time and temperature, the latter should pay attention to the patch temperature, the most important is the price, many manufacturers in order to cost savings, internal chip used is too small does not meet the standards, support steal frugal material, with iron, the failure cycle shortened, LED lamp can not reach the ideal effect. Again, the LED supply current must not exceed the rated value, which is an important factor in damage to lamps and lanterns
Q:The quality of the LED patch module
Chip size. The larger the size of the same chip, the higher the general brightness, the stronger the bearing capacity, the higher the stability performance, of course, the price is relatively high. The size of the module chips now includes: 9MIL, 10MIL, 12MIL, 14MIL, 23MIL, and so on.
Q:How to install the patch LED lamp band?
More attention is paid to the lamp with waterproof and the installation of a solid in the outdoor installation, outdoor installation often adopts the mode of fixed card slot, need to cut and connected place, and indoor installation, just need another with waterproof glue, waterproof effect to consolidate the connection point.
Q:Patch LED features
The principle of luminescence is that of cold luminescence, not by heating or discharging light, so the component life is about 50~100 times longer than that of tungsten filament bulb, and about one hundred thousand hours.
Q:What is the difference between SMT LED packaging with silicone and epoxy resin transparent package? What is the market situation of these two types of packaging?
At present, it is basically made of silica gel, and the epoxy resin is very few. Only those with lower price may use some. Why is it rare to use epoxy? Because of the use of LED epoxy patch cited some discomfort because the cable used in the above: reflow welding, high temperature resistant epoxy epoxy and silicone not lead to separation, produce decay dead lights etc..
Q:What are the storage requirements of SMT patch LED (LED)?
Moisture-proof packing- anti SMD LED in the transport and storage of moisture absorption, SMD LED shall be placed in sealed moisture-proof bag, inside put damp proof agent for protection, and placed the humidity humidity SMD display card packaging bag.
Q:How does the LED patch lamp differentiate between positive and negative poles?
The light emitting diode is fixed regardless of color. The light emitting diode 1, line: foot length is positive, the negative is short. The electrodes inside the tube can also be carefully observed, while the smaller ones are positive and the large ones, similar to the bowl, are negative. 2, SMD: overlooking the side with the color line is negative, the other side is positive.
Q:Patch LED beads can be bought in what place?
If you don't want to constantly change with it, suggest you go to OSRAM, Nichia, Corey, Taiwan Tongjia enterprise authorized agency purchase.
Q:What is the difference between patch LED beads and LED beads: General
A pin of the lamp, and outside a resin cap, because the reason LED beads can spotlight cap;There is no pin on the patch and there is no resin cap outside. Because of the lack of cap, the LED patch can not be concentrated.Patch is based on small power, the shape is relatively small (usually 0.5 and 0.5W products)It's called patch because some small ones need Mounter to machine.The ordinary LED lamp, solder joints than SMD beads, now is the largest artificial welding. Regular watts count from 1-300W
The total area of ​​25,000 square meters. Company R & D, production, sales, service integration, professional development and production of high brightness - blue-white, pure purple pure green ﹑ series of high-end full-color LED (light emitting diode).

1. Manufacturer Overview

Location Shenzhen,China
Year Established 2004
Annual Output Value
Main Markets

Mid East;Western Europe
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Shenzhen
Export Percentage
No.of Employees in Trade Department 60 People
Language Spoken: Chinese
b)Factory Information  
Factory Size: Above 4,000 square meters
No. of Production Lines About 10
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Cheap