knife seat,F-KB023 beech knife seat,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:rubber wood knife seat

material:rubber wood

MEAS:31*22.8cm



Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


Description:

1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.

2、The knife seat was refined by material, assembly, polishing, painting and other procedures.

3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.

4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.

5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure  that  dry and clean and put 


it in the open air


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:What is the cause of the shaking of the turret
Spend some money, from bending machine manufacturers please a teacher to do.
Q:Lathe machining slender workpiece should be matched with the knife
Choose reasonable tool angle; in order to reduce the radial cutting force, should choose the larger main angle; the front cutter surface should be grinded chipbreaker R=1.5-3mm, the chip flow surface to be machined; the tool surface roughness to be small, and keep a sharp cutting edge.
Q:How do you know how to install the roller skates?
If you are able to disassemble the wheel of the kind of one-piece knife, the general is divided into 165 holes and the distance between the 195 holes, the general number of roller skates is the distance between the 165 holes of the.When installing tool holder is according to personal habits, but most were filled with the knife knife mounted on the middle sole. That is, the wheel is about the same length as the shoe. This is more comfortable. Of course, there are special requirements in order to toe and heel action to do better, but also will be installed on the front or back.
Q:NC turret is not in place
Holzer element and outer ring position are not good. Please check.
Q:Why do some tool holders require low level inputs
In a word: your signal circuit IC no internal resistance, protection. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. Pull on the device is the injection current, the output current is down; just pull the weak and strong resistance, no strict distinction between what; for non (collector or drain) open circuit output circuit (such as gates) current and voltage capacity improvement is limited, the pull-up resistor is the main function of open circuit output type of circuit output current for the collector channel. All the pull-down resistor pull-up resistor is used in logic circuit, the circuit current is very small, the logic circuit of MOS tube bias current is microampere, even pA uA, the current level to provide a desired level, such as the current level without any output, because there is a pullup resistor so after a level is actually connected to a high level. Power amplifier circuit with no pull down resistor. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. The pull-up resistor is the main function of the open circuit output current output channel for the collector; main function is connected with the pull-down resistor resistor together to line in the closed circuit driver (node) to a fixed level. Pull on the device is the injection current, the output current is down to note is that the pull-up resistance caused by too large delay output level, including the choice of the principle of resistance: 1, from the current irrigation ability to save the power consumption and chip considerations should be large enough; resistance...
Q:How to distinguish the front tool holder and the tool post
The turret of the numerical control lathe is the front knife holder in the operator's side. The common lathe is the rear cutter. When the tool head, the G42 tip radius compensation right bias in the car when the hole, when the car is round with G41.
Q:Why is the number 980 CNC lathe turret always turn and then alarm
What is the alarm? If the information is only in the parameters of the interface will not be canceled after the pop-up bar. If the alarm is always there must be an alarm number.
Q:How to return to the ordinary lathe tool
This problem is due to the positioning of the positioning pin hole under the knife body broken and small pallet wear caused by knife positioning, it must be replaced to accurate positioning pin and a positioning sleeve.
Q:How can we remove the NC turret
First remove the inside, then the following,Two screws inside, then the eye, should use a punch, turn down
Q:What are the advantages and disadvantages of CNC lathe turret
Tool holder is a very important part of CNC lathe. The structure form of the general lathe for rotary cutter is mounted on the carriage along the circumferential direction, radial and axial turning tools can be installed, drilling and boring. The machining center can also be equipped with an axial milling cutter and a radial milling cutter. A small number of CNC lathe tool holder for the straight row type, cutting tool installed along a straight line.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range