knife seat,F-KB004 acacia wood knife seat and chopping board,your best choice

Ref Price:
Loading Port:
Guangzhou
Payment Terms:
TT OR LC
Min Order Qty:
1000 pc
Supply Capability:
100000 pc/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

product name:acacia wood knife seat and chopping board

material:acacia wood

N.W.:2.008kg

MEAS:26*25*8cm


Specifications:

Has the quite distinct shape of the mountain wood grain, and the contact surface is a good sense

Excellent toughness, process into various curved according to the needs , full of beauty

Solid texture,manufactured goods with firm structure,prolonged service life

The texture of rubber wood is fine and closely woven,pore full of lots ot padding so it's hard to absorb water and corrode.


Description:

1、The knife seat use material of high quality natural acacia wood and take professional advanced machine equipment and manual binding.

2、The knife seat was refined by material, assembly, polishing, painting and other procedures.

3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.

4、Hoteam commerce co.,LTD,is a manufactory specialized in all kinds of wood knife handles,wood seats,chopping boards and other woodworks.

5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure  that  dry and clean and put it in the open air


acacia wood knife seat quantity:

Safety, health, bright color,durable,the everyday necessary good products

Anti-mildew change,anti moth

Environmental protection,no crack,no decay


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:How to return to the ordinary lathe tool
Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear. Wear badly needed to repair or replace.
Q:How to save the supermarket roll bag?
The market has a rolling bag buckle machine, a hand can pull a bag, not a pull on several only, and that the user to pull two times as long as two, on the one hand can reduce the excessive waste of plastic bags and bags of rolling customers pull out of the waste, in general customers put a lot of tear rolling bag home as a garbage bag or a small number of people, you can also do some publicity
Q:The structure and working principle of 4 position tool holder
4 position tool holder structure of numerical control vehicle:Under normal circumstances can be fitted with 4 knives, the knife holder inside a worm with a turbineThe knife and the base on the contact surface of one end gear and two limiting block, the upper surface of the base two end face gear engaged normally a motor and worm shaft.The principle of 4 station tool holder for NC lathe:The knife is receiving the instructions in the form of pulse waves, when receiving a tool change instruction motor drives the turbine and worm. The worm to rotate the cutter knife up end gear separation, when the turret is elevated to a certain extent, together with the turret turret rotation worm together, rotate 90 degrees after encountering a limit block, because the motor power is blocked to when starting to reverse, the natural turret decline on the base end gear limit block lock, complete tool change
Q:Why do some tool holders require low level inputs
In a word: your signal circuit IC no internal resistance, protection. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. Pull on the device is the injection current, the output current is down; just pull the weak and strong resistance, no strict distinction between what; for non (collector or drain) open circuit output circuit (such as gates) current and voltage capacity improvement is limited, the pull-up resistor is the main function of open circuit output type of circuit output current for the collector channel. All the pull-down resistor pull-up resistor is used in logic circuit, the circuit current is very small, the logic circuit of MOS tube bias current is microampere, even pA uA, the current level to provide a desired level, such as the current level without any output, because there is a pullup resistor so after a level is actually connected to a high level. Power amplifier circuit with no pull down resistor. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. The pull-up resistor is the main function of the open circuit output current output channel for the collector; main function is connected with the pull-down resistor resistor together to line in the closed circuit driver (node) to a fixed level. Pull on the device is the injection current, the output current is down to note is that the pull-up resistance caused by too large delay output level, including the choice of the principle of resistance: 1, from the current irrigation ability to save the power consumption and chip considerations should be large enough; resistance...
Q:Why use the center and the rest?
Because, when processing the slender shaft, the process system rigidity problems, mainly for the slender shaft rigidity is low, the cutting force (radial force) under the action of bending deformation (elastic deformation), car axle, a middle drum. The center frame or the tool holder is used to counteract the radial cutting force and increase the rigidity of the slender shaft.
Q:CNC turret can be turned into 45 degrees ah? Can you turn counterclockwise?
8 position of the numerical control turret, each turn 1 knife is 45 degrees, can be positive and negative (that is, clockwise and counterclockwise rotation)
Q:What is the reason why the turret of NC lathe is not maintained?
Yesterday, just repaired a CNC lathe, is the tool holder to turn around, open the lid above the knife, and found that there are water, wipe the test machine is normal, is the problem of sealing the lid is not strict.
Q:What is the difference between NC machine tool and tool holder
In front of the turret with rear turret X axis is not the same, the general system programming does not have what difference, the front turret program got rear turret lathe bed on the same processing, but also have different, like Beijing DTM window system, front and rear arc knife tool that is just the opposite.
Q:How to distinguish the front tool holder and the tool post
Whether NC or normal car, a knife in the side is the pre processor, or post, either rear or front, when processing with radius compensation are determined according to the post, the outer circle with G42, G41 in the hole.
Q:NC turret is not in place
The switch of the tool holder (the encoder or the encoder) is loosened and displaced.First manually pull the motor rotation, so that the tool holder is in position, in the system diagnostic interface to view the cutter position signal, back and forth rotation of the tool holder switch, so that the current knife position signal in the diagnostic page display, and then tighten the tool holder switch.One more word, position detection in ordinary turret is actually a switch, just a different type, divided into contact and contactless or integrated multi position switch, and can not complete the encoding encoding, is in the NC system, called frame encoder has high technology content, the price is much more expensive. The knife switch is not worth some money.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range