High - End Galvanized Steel Door In China

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
3 set
Supply Capability:
2000 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Detail Specifications


1:Steel sheet of door panel

0.3 ~ 1.0mm cold rolled steel sheet

2:Steel sheet of door  frame

0.7 ~ 2.0mm cold rolled steel sheet

3:Frame outer sizes (HxW)

2050 x 860mm / 960mm, or customized size

4:Thickness of the door leaf

50 / 70 / 90mm

5:Opening direction

Left inside / Left outside / Right inside / Right outside

6:Inner filling material

Honeycomb paper / Rock wool / PU foam

7:Rubber sealed:Double-layer rubber sealed strip around the door

8:Door sill-High quality stainless steel threshold

9:Doorbell--Invisible alarm doorbell ( both practical and beautiful)

10:Peephole-Wideangle peephol

11:Hinges-Galvanized steel hinges

12:Surface treatment

Bright, lustrous and durable appearance, the door surface via acid cleaning phosphorizing antirust processing

Heat-transfer printing on surface: looks like the natural wooden grain. Or powder coating on surface

13:With high quality burglarproof lock;ABC lock-set with 13 lock points


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Aluminum alloy door seal lush dripping drip how to do?
Like this situation is generally the lower frame material level to play drainage holes or drainage holes are too small, there is a situation is not the location of the drainage hole caused by a rain caused by the indoor under the box material leakage of water leakage situation. This situation can be their own solution, but also to find the master of the doors and windows to solve. The solution is the same. That is, in the lower part of the box on the outer edge of the left and right to open a drain hole. Note; can not open a drain hole, because the wind pressure problem, open a wind pressure water or row does not come out, so open two. Drain hole can not play too deep, just penetrate the profile wall can be, whether it is flat window or sliding window position to play in the lower frame on the plane can be, do not hit the interior of the profile chamber. tool. Hand drill, 5mm twist drill bit.
Q:Do you need to do a production license for aluminum doors and windows?
According to the "building outside the window product production license implementation of fine" requirement: Where the building window products are produced, sold or used in business activities within the territory of the People 's Republic of China, the present Regulations shall apply. Any enterprise that does not obtain a production license shall not produce the building window products. No unit or individual may sell or use the building window products that have not obtained the production license in the business activities.  The rules apply to the construction of the window products to implement the production license management of the building outside the window: aluminum alloy construction profiles, window frames with unplasticized PVC profiles, color coated steel and steel profiles made of building windows The Building windows of the product unit: aluminum windows, plastic windows, color coated steel window window.  The State Administration of Quality Supervision, Inspection and Quarantine (hereinafter referred to as the General Administration of Quality Supervision, Inspection and Quarantine) is responsible for the unified management of the production license of the building window products. Unified release of the provincial quality and Technical Supervision issued by the product catalog and timely adjustment, unified development and promulgation of product implementation rules, unified provisions of the certificate style, and to take occasional inspection of the provincial quality and technical supervision of the issuing work Quality supervision and inspection.        According to regulations, any units and individuals operating outside the window products must obtain a production license, otherwise they shall not produce or sell. Therefore, self-employed also need to apply for production license.
Q:Aluminum alloy doors and windows of the top of what kind of good There is no physical look
Teach you a move, the choice of hair, the first in the glass, such as "non-absorbent place" drops a few drops of water, the top of the wool will be immersed in a few drops of water, if the top of the hair is not absorbent " Dripping did not change ", indicating that the quality of this hair is excellent, it is worth buying.
Q:Aluminum alloy doors and windows profiles 80,868 What does it mean?
Section is not the same Let's talk about the structure of aluminum alloy doors and windows: aluminum windows and doors windows and windows and windows and windows in two parts; window frame is a fixed part and the wall connection; sash and window frame is connected to push or flat open that part; 80,868 refers to the window frame profile outside the measurement thickness, not the thickness of aluminum; 80 on behalf of the aluminum frame profile size 80 thickness is 80mm, 868 is 86.8mm; The larger the number, the larger the thickness of the profile is, and the firmness is firm; the cost is high;
Q:Bathroom aluminum door handle lock how to lock the cylinder
Disassembly method: Remove the inside and outside of the two handle panel: the screw in the handle on the panel, the top one, the following one. 2. Remove the inside and outside the lock cylinder cap: screw in the house lock on the cap, that is, plug the left and right sides of the key. 3. Lock the cylinder positioning screw: the screw on the side of the door, in the middle of the lock, with the same height cylinder. The thickest is that. 4. At this time you can remove the old lock cylinder: the old and new lock cylinder, you can replace the. Install new lock cylinder: Order and split the opposite, pay attention to the following points: 1. Before installing the new lock cylinder, add a small amount of lock cylinder to the new lock cylinder dedicated lubricant. Repeat the lap with the key. 2. Cylindrical positioning screws must be tightened to prevent the screw after the opening is not good to open the door. 3. Lock the cap screw Do not twist particularly tight, to prevent the call, bad unlock. 4. When installing the inner handle panel, there is a fuse at the bottom, insert the corresponding fuse.
Q:How do aluminum windows and doors eliminate static electricity?
How to prevent and eliminate static electricity? The key to maintain the humidity of the surrounding environment, and minimize the factors that lead to static electricity. First, the room to maintain a certain degree of humidity. The room to ground, ground sprinkle some water, or use the air humidifier to increase humidity. Second, to take a bath, change clothes, to eliminate the accumulation of static charge on the surface of the human body. Third, less wear leather, wool and chemical fiber texture of clothing, especially the elderly, should try to wear soft, smooth cotton or silk clothing. Four, usually drink plenty of water, wash your face, wash your hands, hair can not be combed, the comb soaked to eliminate static electricity after combing hair. 5, after stripping and contact with metal products, the first hand touch the walls, the physical release of the static electricity. 6, cleaning wool clothing, the use of clothing softener, etc. In addition to electrostatic cleaning supplies, this can reduce the static electricity generated when wearing.
Q:how do i measure and cut to install a door in my block concrete garage wall. i have a 36 metal door.
Assuming your door is pre-hung, measure the jamb width (not the molding attached to the face of the jamb). Add 3 1/4 inches for your 2x8 lumber, ( you did buy treated didn't you?). Add another 1/2 inch for room to plumb the jamb in the opening. (I'm afraid you have to go back to the store to buy shims...get some great-stuff for doors and windows while you're there.) Measure height of door jamb. Add 1/4 inch for leveling. Mark wall using level. Cut blocks with concrete saw you rented while you were out buying shims and great-stuff. Pray wall doesn't tumble down on your head, ( You did remember to consult a qualified engineer. It's much better if you pay them to take the blame when things go wrong.) Fill voids in wall with mortar or cement. Tapcon treated 2x8 to opening using a generous amount of liquid nails I forgot to tell you to buy. (Back to the store again...you actually had tapcons and a hammer drill?). Finally...the door. Get out your six foot level and your three foot level. Shim bottom of door on hinged side about 1/4 inch. Plumb hinged side up shimming as needed. level across top. Plumb down other side. Use shims behind every screw. (You did buy screws). Fill voids with great-stuff. Caulk. Paint. Lightly oil hinges. Enjoy :)
Q:What are the differences between aluminum doors and windows and steel doors and windows?
The difference is that the material is different, aluminum and plastic steel difference, aluminum alloy doors and windows are made of aluminum alloy, the appearance of good-looking, easy installation, high-quality aluminum doors and windows of high strength, but the insulation effect is poor, The existing broken bridge aluminum alloy window, the practice is divided into two parts inside and outside, the middle of the connection with nylon, nylon from the block to play the role of temperature, but the high cost. Plastic doors and windows at the beginning of the plastic doors and windows, that is, made of plastic frame material frame, and then the joints hot melt bonding together, the advantage is good insulation effect, but the overall strength is poor, Increase the steel lining to improve the strength, and retain a good sound insulation effect, so very fashionable, performance as a result of the process of upgrading the program, and now basically almost the same, but with the performance of doors and windows, or steel cheaper.
Q:Does anyone know if I can buy metal door handles for a Suzuki Samurai?
There is not a metal handle available. You could have a machine shop make them but that would be expensive. I am a Tool and Die Maker and can tell you that this would be several hours of work.
Q:How do I paint a metal garage door and what type of paint do I use?
If your door has loose chips scrape off the loose paint,since this is metal if bare metal is showing you need to buy a metal primer. Then paint your door with 2 coats of acrylic paint.acrylic paint is more flexable and will last longer on items that have movement. These item can be purchased at most lumber yards,lowes,menards,walmart

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range