F-KB037 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：rubber wood
N.W.：0.98kg
MEAS：21*15*6.5cm
Description：
1、The knife seat use material of high quality natural rubber wood and take professional advanced machine equipment and manual binding.
2、The knife seat was refined by material, assembly, polishing, painting and other procedures.
3、The knife holder has the advantages of real materials, excellent workmanship, mouldproof and moth proofing, anti bacteria, wear-resisting etc.
4、Hoteam commerce co.，LTD，is a manufactory specialized in all kinds of wood knife handles，wood seats，chopping boards and other woodworks.
5、Because the knife tool contact with tool wet food for long time, is very easy to breed bacteria, you should ensure that dry and clean and put it in the open air
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
Main Export Markets:
Eastern Europe North America
Mid East/Africa Central/South America
Asia Western Europe
Australasia
- Q:CNC lathe tool holder clamping bit how to clip
- If it is a square knife, just to make a fixture, clamping on the tool holder, tooling with Morse 4# internal cone, the inner cone can be fitted with a drill chuck, can also be directly fitted with taper shank drill.
- Q:Drilling out of the hole is the overall deviation, the hole is 0.15, the cutting tool angle is not biased, the product is not how to jump, I was the first drilling after the chamfer, is how to go wrong, in this case, ask the teacher, thank you first, urgent...
- The overall mean partial is specific bit big?1 first check the bottom of the hole with the size of the hole is the same if it can not be determined for the drill bit tilted2 drill bit size is not accurate in general has a few wire error is normalIf you are talking about the normal eccentricity the central axis of the hole is not a shaft with the central axis of the workpieceSo it is the problem of the chuck first clean the chuck jaws necessary when the car can claw a knife and then try to solve the problemIf not, that's the problem with the chuck assembly
- Q:What is the difference between the NC lathe and the tool post
- Also, the most important thing is to look at the direction of the knife, there are positive and reverse difference, that is, M3 and M4
- Q:CNC machine tool can be drilled hole how to center
- 1, do not need to set the coordinate system (the center), is loaded with a knife, in the process of preparation of processing requirements, reasonable adjust the height and verticality, the proper use of speed and feed rate, the knife tool can be set, simple, can fix a hole.2, if the degree of difficulty and high requirements, please use the circular drilling instructions programming.
- Q:NC turret is not in place
- Holzer element and outer ring position are not good. Please check.
- Q:The cutting surface of the optical fiber cutter is like this, what's going on?
- Carefully close the cutting knife to see whether the two sides of the rubber gasket is intact. If intact, carefully observe the top blade to contact fiber piece arc area not intact, then the level of direction was much higher than the top blade gasket, with a 1.5mm as a benchmark, try not to go down fine cutting. The time can shake head check guide rail wear, wear, cutting blade to promote instability, how to adjust is good, the general cutter is used in the IKO guide, should not be so easy to wear. Unless cottage.PS is now some cutting knife, fiber clamp is not good to put the bare fiber will be placed when there will be such an end face.This is the way I transferred, upstairs from the next should be better.
- Q:For what parts of the process, what is the difference between the installation
- With the knife is like a long knife, to prevent the use of knives to make the knife, the center frame is used for the processing of slender shaft, to prevent the processing of slender shaft shape into the middle of the coarse two fine
- Q:CNC lathe hit the knife after the knife center height, how to deal with?
- Maybe the dowel pin is misplaced,tool change pin
- Q:How to save the supermarket roll bag?
- In the place of the roll bag placed in the food and goods, dry and wet varieties, such as the separation of each line of the front of the sale of things, do not half-way and tail placed, mainly with the sale of goods placed matching
- Q:The first reason is that the cutter shaft of the motor shaft is broken for a shaft / how long it will not be able to die!
- Adjust the parameters, the tool change time and lock time, try!
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
F-KB037 Rubber wood knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords
