Acoustic Mineral Fiber Ceiling with Texture MA03
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
Standard Size:
Edge Detail:
Square edge for
Tegular edge for
Micro-lock tegular edge for
Available Textures:
Astral Series: MA01, MA02, MA03, MA04
Perforated Series: MP01, MP02, MP03
Fissured Series: MF01, MF02
Sand Series: MS01, MS02
Customized textures are also welcome ifbuyer pays for new-mould charges.
Technical Data:
Density (kgs/m3): 240-280kgs/m3
NRC: ≥0.45
Fire resistance: class a qualification(GB8625-88 STIPULATION)
Moisture rate (%): ≤3
Light reflect: 0.60-0.80
Bending strength(N): ≥60
Sagging resistant properties:≤
HR: ≥90%
Main Advantages:
High humidity resistance properties
Excellent light reflectance
Environment-friendly
Wonderful sound-absorption
No content of asbestos
Zero release of CH2O
Economical Choice
Typical Application Areas:
Hotel Lobbies and Corridors
Offices and conference rooms
Auditoriums
Hospitals and other Public Site
Department stores
Super Malls
- Q:Accord 9 left door door trim how to split ah?
- Tools: flat screwdriver, 8 socket wrench Steps: 1, with a flat screwdriver down to pry open the door handle lower trim, from the middle down and then pull out (the back door is the pry half of the front) 2, remove the handle under the veneer can be seen after the internal two black eight hex bolts, with a socket wrench down 3, unplug the window lift switch plug (which has a clip, use your fingers from the back hook to pull out) 4, with a flat screwdriver from front to back pry open the door handle trim panels, remove the door when the handle 5, hand the door trim below the mouth a little open a gap, and then put a wrench into the pry, that the interior board is a plastic card with a plastic card buckle on the door, the pry when the time to use a little effort, One by one pry. If you want to wrench the plastic interior trim bad, you can use a little steel bars and the like, but not too thick, or can not reach into. 6, a lap card bamboo shoots all pry open, hold the door trim board can be removed from the bottom up.
- Q:What are the functions of inorganic pre-coated decorative panels?
- Inorganic precoat decorative panels in the international community refers to the inorganic non-combustible material as the substrate, the surface of a special process with a decorative coating, the final form can be directly installed without the use of surface treatment of decorative plates. Inorganic precoat decorative board of the substrate requirements are higher, requiring the material itself is better strength, impact resistance, bending, bending, fire, light, water absorption, acid, alkali, thermal expansion coefficient, temperature difference The Inorganic precoat decorative panels are mainly coated with fluorocarbon coating, inorganic ceramic coating, polyurethane coating. Fluorocarbon coating because of its fluorine molecular characteristics, so that its surface with excellent performance, weather resistance, acid, alkali, scrub resistance and other properties are excellent performance, and its rich color, glossy, Is unmatched by other materials. The inorganic ceramic coating in the main performance and fluorocarbon coating equivalent in the surface hardness is higher than the general coating, is mainly in foreign production, domestic only individual manufacturers can produce similar homogeneous plate. Polyurethane coating in all respects with fluorocarbon coating, inorganic ceramic coating has a certain gap, mainly for interior decoration.
- Q:Conventional decorative panels, decorative plate construction process is to paste the glue to the grass-roots board or fixed with a nail in the grass-roots board, I would like to ask this process "glue method, nail"
- The key depends on the stability of this carbonized wood decorative panels, whether it will moisture expansion deformation, If you can ensure stability, you can secretly fight. The so-called "seamless" is only relative to the process of sewing the construction process, is not seamless, but the seam is very fine, less than 1mm, 0.5mm or so.
- Q:Where the United States insulation composite decorative plate is what material factory
- Energy-saving insulation board according to insulation core material type is divided into: organic insulation board and inorganic insulation board type. ?? - Organic insulation board: Insulation material can be molded polystyrene board (EPS board) (physical properties: low density, low tensile strength), extruded polystyrene board (XPS) and rigid foam polyurethane or polyurethane board. ?? - Inorganic insulation board type: insulation material can be expanded glass beads, expanded perlite plate and foam glass plate and other inorganic insulation board. ?? Insulation decorative panels according to panel type is divided into: paint panel type, non-painted panel type. ?? - Paint panel type: panel can be aluminum, steel, aluminum composite panels, inorganic resin plate, such as fluorocarbon paint layer. ?? - non-lacquered panel type: panel can be natural stone plate, wall tiles, pottery plate, etc., such materials and decorative properties such as traditional curtain wall
- Q:How do the van side of the van?
- Van side door plate dismantling method: 1, open the car side door, the glass lift on the rocker on the small cover with plastic sheet tilt, remove the screw to remove the rocker. 2, the glass below the lock door button on the clinker button down. 3, if it is glued to the door skin, with a plastic knife from the side into the next look next to look up, if it is buckle, with a word tool to buckle up the door can be decorated down the door trim.
- Q:Pentium 70 door mounted sound insulation cotton trim board card card is not tight what is the reason
- Hello, this situation, it should be you put the sound insulation place wrong!
- Q:Is the elevator decorative color stainless steel decorative plate used?
- Stainless steel elevator doors because of its decorative effect and corrosion resistance are far superior to ordinary stainless steel, its wear resistance, anti-characterization, scrub resistance is better than other stainless steel. And the processing performance and other aspects of performance are the same as ordinary stainless steel, color surface layer does not fade, the color varies with the light angle will produce different characteristics such as color change, and color surface layer temperature 200 ℃, salt spray corrosion resistance ratio General stainless steel is good, wear and scratch resistance is equivalent to the performance of the foil layer of gold. When bending 90 ℃, the color layer will not be damaged, can be used as hall wall panels, ceilings, elevator panels, car panels, construction and decoration, signs and other decorative purposes. Stainless steel elevator door, not only durable, beautiful and novel, but also has a strong sense of the times. Color elevator decoration materials from the choice of color stainless steel. Through the stainless steel color stainless steel surface treatment processing methods for a single or multi-process combination, thus forming a unique, three-dimensional strong decorative panels. Common color elevator decoration materials are mostly color drawing etching pattern plate, color mirror etching pattern plate, or multi-process drawing, mirror, etching, sandblasting, and pattern, the plating color is also reflected in a decorative panel.
- Q:What are the characteristics of insulation decorative panels
- Here we have to TDD exterior insulation decorative board as an example to introduce the external wall insulation decorative board this new building materials advantages. First, for everyone is well aware of the most valuable advantage is the ability to play on the building insulation function, making the building to achieve the effect of Dongnuanxialiang. Due to the physical properties of the insulation board, the winter can keep the temperature, the summer can block the external temperature, making the indoor temperature to maintain a relatively stable level. Second, because the external wall insulation material to protect the walls of concrete and brick walls from external erosion and damage, so the insulation board is also able to extend the service life of the building. At the same time, because the external wall insulation decorative board to keep the room temperature stability, but also can play a protective building wall does not appear cracking, deformation of the situation.
- Q:Uv decorative plate how long does not fade
- There are two general UV board surface, one is a kind of indoor outdoors
- Q:Formaldehyde is one of the most common pollutants released by some inferior decorative board materials?
- Yes, formaldehyde commonly known as formalin, is colorless, with a strong smell of irritating gas, its 35% to 40% of the aqueous solution known as formalin. Formaldehyde is the original pulp poison, can combine with the protein, inhalation of high concentrations of formaldehyde, there will be severe respiratory irritation and edema, eye pain, headache, bronchial asthma can also occur. Skin direct contact with formaldehyde, can cause dermatitis, stains, necrosis. Often inhalation of a small amount of formaldehyde, can cause chronic poisoning, mucosal congestion, skin irritation, allergic dermatitis, nail keratosis and fragile, nail bed finger pain, long-term inhalation of pregnant women may lead to neonatal malformations, and even death, Leading to male sperm deformity, death, decreased sexual function, serious can lead to lack of reproductive capacity, systemic symptoms are headache, fatigue, poor appetite, palpitations, insomnia, weight loss and autonomic disorders.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Acoustic Mineral Fiber Ceiling with Texture MA03
- Loading Port:
- China Main Port
- Payment Terms:
- TT OR LC
- Min Order Qty:
- -
- Supply Capability:
- -
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords