Q:In the old composite wood flooring and then add a layer of elephant composite wood flooring is possible, will not exceed the formaldehyde content

Can not, for the reason there are three first, chu chu gangsters to see the color of coloring Kyrgyzstan is always aware of the problem, so the following layer of floor there will be a wet phenomenon, the smell is not good third, a long time easy to breed Insects, but also a small strong living environment

Q:I did not pretend to repair? Asked, the decoration when the ground to go a lot of pipelines, need to be buried below the ground? If not interdiscuous melon melon scallop pigeon sleep Gong Jing buried, pavement composite floor when the ground is not how to do ah? Another bathroom waterproof to be how high ah? More

1, need to be buried in the ground 2, the shop compound reciprocity ingot melon melon scallop pigeon sleep Gong Jing board requirements ground level, so the uneven must be leveling. Uneven use of cement leveling, not serious with gypsum powder leveling. 3, waterproof bath over there to do more than one high. Experience is for reference only.

Q:What is the plastic floor? What is the composite floor?

Plastic flooring generally refers to PVC flooring, as well as wood flooring. The floor has the material of the material, water resistance, generally suitable for public places. Composite floor, in a broad sense, refers to the structure by the layers of composite floor, such as: laminate flooring, multi-layer parquet, part of the bamboo flooring. As for the floor resistant to burning cigarettes, there are provisions of the national standard. PVC flooring, laminate flooring and other surfaces are often exposed to the end of the seal all over the full set of aluminum oxide wear layer, more resistant to burning, the general bamboo, wood flooring surface is paint,

Q:engineered flooring knowledge?

I have some knowledge of engineered wood floors. They are a viable alternative to regular hardwood floors but not as forgiving. They are wood but in fact they are essentially modified Pergo (plastic flooring). Given the choice, I would go with hardwood over engineered wood floors, Pergo over engineered wood floors. Just my opinion

Q:What is the price of a composite floor?

More than 100 bars

Q:I have purchased all the wood and am having a guy install my wood floor. I've purchased a good adhesive to get the floor to adhere to the concrete underneath. Now I am wondering if I need a glue to slather into the tongue and groove joints? Your thoughts?

If you have the proper glue to adhere the engineered wood to slab you most definitely do not need any glue for the tongue and groove. You only need the special sized / shaped trowel. Gluing the t/g together is only done when creating a floating floor system from engineered wood. Any questions you can e mail me through my avatar. GL

Q:Solid wood composite floor suitable for installation to warm it?

Pavement must pay attention to check your home to warm the pipeline and all buried in the floor under the water pipe installation is scientific, followed by the choice of the appropriate solid wood flooring. To warm wood floor selection criteria 1, the floor size is stable, can withstand the temperature change is not damaged. 2, no deformation, cracking, thermal expansion and contraction coefficient is small. 3, environmental protection, no formaldehyde and harmful gas release. 4, not afraid of water soaked floor (to prevent damage to the floor of the geothermal pipe damage). Solid wood flooring and composite floor comparison 1, in general, the composite floor is more suitable for use to warm the floor. Because the standard thickness of the floor is 6.5 ~ 8.5mm, the thickness of the composite floor is mostly 6 ~ 9mm, of which the laminate flooring is mostly 6 ~ 8mm, the three-layer parquet is 8 ~ 9mm, the heat transfer performance is better, and its The surface layer of aluminum oxide wear layer, the wear layer is conducive to the rapid spread of heat on the surface. 2, solid wood flooring in the general thickness of about 2cm, the installation should also play keel, used to warm the floor, then the floor and the ground between the air, air and wood thermal conductivity are very low, so heat is not easy to conduct to the surface, will lead to The waste of heat, the surface temperature is not uniform, the temperature difference is obvious, and the composite floor after high temperature suppression, the internal moisture content is very small, so the floor will not be due to the loss of moisture and deformation. Multi-layer solid wood flooring between the layers of each staggered, each containment, the back there are dense anti-deformation trench, decomposition of the heated surface stress, so the deformation is very small.

Q:I had a chemical spill on part of an engineered floor that I laid down a few months ago (the glued down type). Now I need to repair it, but have two problems:1. How do I do it, because there is a toungue and groov on every edge, so I cant figure out a way without removing half the floor (to the wall).2. I am having trouble getting up the old flooring because the glue sticks so well. They sell long-handled scrapers at the store, but I suspect that it wouldn't work at all. I have tried both a chisel and putty knife, but can only remove an inch every 10 minutes. A grinder with a grinding wheel causes lots of burning, and I risk damanging a nearby plank. Is there an easier/faster way?

I set a circular saw to the depth of the board and cut a section out. Taping off surrounding boards w/ a painters tape so I dont cut to far since the sawdust will seem to hide the next board. Then with a chisel I chisel that piece out ..Very carefully!! Then chisel the tounge and groove section in toward the middle. Elbow grease and a sharp chisel and scraper are the only way to go.. then you ll have to cut off the tounge part by setting the blade just to the top of the tounge so you don t damage the edging.. Trial fit all boards, then glue down and you ll have to top nail and fill in nail holes.. If your on cement you ll have to put weights atop till the glue sets. It s a downfall of any glue downed floor but it s the only way sorry GL

Q:Can the composite floor be installed,

The premise is that you will install the case

Q:If you want to shop on the original floor with laminated flooring what needs attention?

1, the original floor is a tile or composite floor, if the tile can be directly shop, but in the kitchen and bathroom joints to seal, to prevent moisture into. 2, if it is on the floor and then shop, to ensure that the original floor smooth, dry, because a number of the bottom floor deformation, the upper floor will be deformed. At the same time also consider the floor increased, the door should be shortened, the composite floor and the original tile floor of the convergence problem. (1) Solid wood floor flatness: If it is very narrow old wooden solid wood flooring, if there is uneven treatment. Such as loose, fixed firmly; if it is Alice, you can planing. Or simply remove one or two pieces, because the smaller area, does not affect the composite floor pavement. If it is wide board, to plan to deal with good. (2) check whether the sound of solid wood flooring, what causes, loose keel or loose floor. (3) keel integrity. Check the keel is loose, there is loose, to re-reinforcement; check whether there is rot, if the decay of aging, replace the new keel. Because the joint effect, if the keel is not good, will have a new composite floor impact. (4) all with more than a few years of solid wood flooring, in the floor before the composite floor, it is best to use the United States solid nail keel reinforcement.