Q:RTBrother recently understand the injection mold related knowledge, about the forming cycle of this problem, I do not know whether this cycle can be estimated according to the relevant parameters, please advise!Forming cycle: the time between the previous product and the next product, including the time taken by the manipulator, and so on. I am for the new quotation, not too precise, but not too far away, trouble expert advice, small first, thank you very much!

If a trial can be used to test out the stopwatch + wide release time, not the trial production of new software available for calculation, but the structure of a product cycle also depends on the size and thickness of the product, is complex and molding technology to all of these affect the product cycle, your statement is not very clear and it is difficult to give you a more accurate estimate of the cycle, experienced personnel can structure size, thickness, the product was estimated, and more reasonable!

Q:Injection molding machine, blister machine, blow molding machine, what is the fundamental difference?

Injection molding machine - a machine that produces plastic products by filling the mold with pressure.

Q:How to check the mold opening stroke of injection molding machine

The mould opening stroke of the injection machine should meet the need of separating the mold and removing the plastic parts. The checking of mould opening stroke is divided into the following several situations.1. the maximum opening stroke of injection molding machine has nothing to do with the die thicknessMainly refers to the clamping mechanism for injection molding machine with hydraulic machinery, such as XS-Z-30, XS-Z-60, XS-ZY-125, XS-ZY-350, XS-ZY-500, XS-ZY-1000 and G54-S200/400 type injection molding machine, the mold opening stroke by the connecting rod mechanism (or clamping cylinder) determines the maximum stroke, irrespective of the thickness of the mold.For injection mold with single parting surface:Smax = H1+H2 + mm (5 ~ 10)For injection mold with double parting surface:Smax = H1 +H2 + +a (5 ~ 10) mmType: Smax injection molding machine maximum mold opening stroke (mm);H1 plastic parts (mm, H1) launched a distance - like mold core is equal to the height, but for the plastic parts of the inner surface is stepped, sometimes do not have to launch the full height core can remove the plastic parts, then H1 can be determined according to specific circumstances, in order to successfully remove the plastic parts;H2 a piece of plastic height, including the height of the castable (mm) of the gating system that is connected to the plastic part.A the distance between the fixed die seat plate and the runner plate required by the casting system to remove the condensate (mm).

Q:Mold opening stroke: 1800/1300mmMaximum opening distance of template: 2000 ~ 2500mmWho can help me explain what these two parameters mean? This is a two plate injection molding machine.

This injection molding machine is quite big! Mold opening stroke: 1800/1300mm refers to the maximum moving stroke of the injection molding machine.The maximum opening distance of the template is 2000 to 2500mm, not the opening distance. It is the maximum distance of the template, that is to say, the largest size of the mold, that is, the maximum shape of the mold.

Q:Name of China's top ten famous brand injection molding machines

Haitian, Donghua, Huada, Iraq and so on, many, many.

Q:Injection molding machine pressure, speed, back pressure unit is what and their relations with other international units

Pressure injection molding machine, we often talk about the pressure, strictly speaking, the pressure is equivalent to the middle school, which bear the force per unit area, the international regulations, under 1N in the area of 1 square meters (Newton) on the pressure of 1Pa (Pascal), as long as know the multiple relation, it is easy to obtain the pressure (strong the conversion unit):1m=100cm=1000mm1kg = 10N1M (megabit, million) Pa=1MPa=1000k (1000) Pa=1000000PaSo 1MPa=10kg/cm^2=1N/mm^2We often use international non legal units of measurement: 1bar=10^5Pa=1kg/cm^2=0.1MPa (bar) and 1Torr=133Pa (Torr)The pressure gauge of the injection molding machine, the most used is MPa, bar, kgf/cm^2 unit, need to be reminded that, behind the two units is not our statutory units of measurement, but the world especially Europe and the United States is often used, because many components of the injection molding machine for imported components, including the pressure gauge, so we will often see illegal dial pressure gauge measurement units.In the injection molding machine, the injection molding machine pressure and back pressure unit is MPa, speed (actually refers to injection rate), the unit is g/s, or cm^3/s

Q:How to change the suction filter core of injection molding machine?

This is simple,The first ready to stop operation of filter, filter box machine behind the clockwise turn can be replaced, not what skills

Q:What is the injection molding machine?

It's a classification of plastic machines! With different injection mold can produce different plastic products, such as home, pots, barrels, hangers, boxes, desk stool, comb hair clips, TV shell, electronics packaging, children's toys, air-conditioning washing machine shell, a large vehicle bumper, windshield, large and small trash, large plastic tray etc. etc.. What it produces is almost everywhere in our lives! Even the mobile phone shell was made out of it. You don't understand anything else. I don't know where to begin!

Q:Why should the central feed system be used in the injection molding workshop?

The advantage of using the central feed system in the injection molding workshop is that:1. save energy2. save labor costs3. improve the company's overall image4. keep the factory environment clean and tidy5., centralized management of raw materials to avoid waste of raw materials and pollution6., can isolate the main transmission, reduce noise pollution"Dongguan niasi" the central feeding system adopts the vacuum conveying mode, through the pipeline system will focus on plastic raw materials from the storage tank is transferred to the central dehumidification system will then transport the raw material after drying to each injection molding machine. "Dongguan niasi" the central feeding system adopts "design a machine of a pipe", to ensure the whole system of raw materials for air transport, to prevent the resurgence of the raw material after drying dehumidifying. At the same time, the pipeline can be cleaned up after each conveying cycle to ensure that there is no residual granular material in the pipeline. The material performance of the injection molding machine is guaranteed to be consistent while avoiding the resurgence of the raw material. Under the vacuum negative pressure, the dust in the raw material will be filtered out through the dust filtration system, which will help to improve the quality of the molding products.Please refer to the resources below for a detailed example of the central feeding system!!!