Q:What are the advantages of butterfly valves?

B. is cheap, especially when the caliber is big;C. the resistance loss is small and the fluid decreases through pressure;

Q:Which is more expensive, gate valve or butterfly valve?

Gate valves of the same material and specifications are much more expensive. The weight of the gate valve is much heavier than that of the butterfly valve.

Q:What do D71, D371 and D341 represent in butterfly valves?

D71 is a handle to clip butterfly valveD371 is a turbine to clip butterfly valveD341 is a manually operated double flanged butterfly valve

Q:What does the triplex of pneumatic butterfly valve mean?

Upstairs is quite right, but now seems to use very little oil mist, and now generally referred to as "triple parts" as if: filter pressure reducing valve, solenoid valve, with the valve position feedback switch.

Q:Butterfly valve in use when should pay attention to what problems?

In the process of using power pipe pneumatic butterfly valve, the need to pay attention to these problems, the first is to conduct a comprehensive inspection in the use of butterfly valve, check butterfly valve is in good condition, all parts are connected in place, the valve is loose and so on, wait to ensure that everything is normal, it can make an official use.

Q:D37A1X9-16CB1: what does this butterfly valve mean?

The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)

Q:The water supply pipe is the gate valve And on the cross dry pipe are the gate valve? To answer the 30

Crown valve pressThere is no standard answer to this question. I can only give you my personal opinionRiser butterfly valve is generally place in these places (the pump outlet valve, drainage system, upper and lower floors) riser are basically installed butterfly valve, butterfly valve is not cheap, fast speed is fast closing butterfly valve can be quickly closed and open educationYou see the water pipe installed valve (with all the cross tube is the basic gate) explanation, because in contrast to the quality and stability, the valve will be better, the site does not need fast switching, it will choose good stability point gateSum upThe drains are all butterfly valves, and the stabilizing pipes are all valves! (do not rule out a full use butterfly valve for stealing work)

Q:Hey YA! I am looking at getting an 01 Honda Prelude this month and valve adjustment keeps coming up when people discuss this car and other cars as well. What is this? Does it cost a lot to do, and is it important? Thank you!

Not at all a big expense most places should do it for $90 -150 including the gasket . Takes me about an hour to do one. If you don't adjust them eventually you could wear the cam possibly although I've never seen any issues from not doing it. If they are too tight then possibly they could've got the engine hot . If they are too loose which is what they should do as they wear they'll just be a little noisy until you get them adjusted if I can help in any other way please let me know hope this helps

Q:What is the effect of nylon coating on butterfly valve plate? Thank you

Mainly media will not be contaminated by rust on the body, you should say that the central soft sealing butterfly valve, the central valve is generally cast steel or cast iron material, so useNylon coatingLining up. There are soft seals, sealing performance is relatively high

Q:Ok, so I took my car in for maintenance (Mustang GT convertible 2002) and the mechanic told me the valve gaskets needed to be replaced and when he gave me the estimate, they were two seperate charges for valve gaskets and valve covers, total of about $250.00 not including labor. Is he trying to rip me off cause I'm a girl by the way? Anyways, I didn't get it done cause it needed something else too and I didn't have enough money so I said I would be back in two weeks. So I called the dealership to inquire about the price and I asked the parts guy for a price on valve gaskets and he was like, I don't know what you mean, we have valve cover gaskets but nothing says just valve gaskets? I told him to give me the price anyways, thinking I would ask my brother (who hasn't tried to help me anyways) and it was $60.00 for both (I need two). How can this be if the other guy was charging me $250.00 for different parts? Help!!! Frustrated and confused, I don't know anything about cars :(

Don't okorder they cost $41.35 for both of them. Fel-pro is the brand name of these gaskets. #2. The valve stem seal kit costs $28.20 and again, Fel-pro is the brand neme. First of all does your car smoke slightly when you decelerate? If not there's absolutely no reason to bother having these seals installed. If the car does smoke when you decelerate valve stem seals are nothing but a stop gap for the real underlying reason the car smokes.