• Unique Design Hot Selling Bathroom Product Tempered glass Light Green Washbasin System 1
Unique Design Hot Selling Bathroom Product Tempered glass Light Green Washbasin

Unique Design Hot Selling Bathroom Product Tempered glass Light Green Washbasin

Ref Price:
$35.41 / set get latest price
Loading Port:
Shenzhen
Payment Terms:
TT
Min Order Qty:
200Pcs set
Supply Capability:
1000Pcs Per Month set/month

Add to My Favorites

Follow us:


OKorder Service Pledge

Quality Product, Order Online Tracking, Timely Delivery

OKorder Financial Service

Credit Rating, Credit Services, Credit Purchasing
Product Size:T12mm×Φ420×H145
Weight:7.5KG
About Product:
1. Glass is tempered which is not easy to be broken.
2. Different kind of design and color on the glass is available.
3. OEM.
Q:How to unclog bathroom sink
used your brains
Q:I am just wondering if it will clog anything.. I don't really care that the necklace is lost because it wasn't very expensive but I just don't want the necklace to mess up anything. I REALLY don't want to open all the pipes and stuff either, messy job. Notice that this is the whole necklace, it was just a silver chain with a cross..So is there any harm in leaving the necklace in the drain?
It okorder /alexrussell/posts/...
Q:Toilet reserved hole size squatting, sitting, urinals, basin and so on
The basin 100 is 100 from the wall
Q:How about the basin down the water
Sure there is no good arc
Q:My family's bathroom is relatively small, so do the wet and dry separation, the basin into the aisle over there, so put the basin at the three walls I posted the wall. But yesterday found that the three walls at right angles, there is not straight, and a big difference. They said that the wall of my house was oblique, but even if it was oblique, it should be cemented with clay. Now we are worried about the time to buy the basin, certainly less than the edge, and can not paste the wall. This is ugly, I LG want to re-posted the wall over there, I would like to ask, that re-posted brick can also use the previous brick? And if not rework, how to solve this corner is not straight, the basin put up to paste it?
Decoration company has not been through it? My home that position to stay in the size of the basin than I bought a little bigger, the decoration company said that playing with silicone should be almost ~ but too much difference is not to re-shop it? Decoration company shop tiles should not be considered when the level and vertical problems?
Q:I need to remove and replace the tail piece for my bathroom sink. I can't seem to actually remove the old one. It is plastic. Any suggestions would be greatly appreciated!
the top part of the drain. the part you see in the sink spins out of the tail piece..if you still can't get it apart and you have the new one take a hack saw and just cut it behind the nut under the sink
Q:Our house was built in 1992. The faucet is old and needs to be replaced. At one point we had purchased a Moen faucet, but the new faucet had like rigid pipe connections whereas the old one has what appears to be soft copper much smaller pipe connections. Im just wondering if this is something that is not easily done. Do they still sell the faucets with the soft copper lines? Or do we need a plumber to do this?
It is not too tough depending on your skills. You will need a basin wrench. You will have to disconnect the supply lines (both hot and cold) and remove the two nuts holding the old faucet in place. Next you need to install the new faucet which is sometimes a two man job, one to hold the faucet straight and the other to tighten the nuts. I suggest you replace your supply lines with flexible lines. Last but not least you will need to hook up the stopper rod that open and closes the stopper in the sink. Well that is how it is done. I figure you can now decide if you want to tackle the job. Good Luck!
Q:How to install the washbasin on a marble countertop
Yes, yes, there is a bracket fixed on the wall. You can measure the size of the doors and windows so that the processing of angle steel processing, you can also buy ready-made, the table more than 1.5 meters with the best three stents, ready-made shelves with support table, a support basin (mainly the audience Pots), marble open basin and the leading hole, the basin stick in the basin position, the basin also use potting reinforcement. Finally on the stent, the general table are both sides of the wall, in the upper part of the wall with the marble processing about 10cm wide waterproof plate, with glass glue or stone glue on the wall. In the lower side of the two sides of the wall is also the same width of the processing of the same width of the retaining plate, sticking to the edge of the table, here is a ready-made stent has a little advantage, that is, the table, the next block, the basin can be supported, , Height adjustable, the size of a little error can also be installed on the retaining water, retaining the water also cover the wall, under the retaining water, beautiful support bracket. On these, and finally loaded the faucet and water. Wall with glass glue or the same color stone filling.
Q:how to unglue a bathroom sink from the wall?
you cant unglue something like that, it can be possible to pry it off the wall if it is sheetrock, the paper on the sheetrock might give before the sink breaks. if it is siliconed around the edges, as some contractors use this as a way to fasten sinks to the wall, then cut it with a utility knife and pry around it as you go. if it is constuction glue on plaster, your screwed unless you have a diamond grinder to cut the wall around the sink and pry it off that way. also, if it is silicone, make sure to cut around the outside edge so you dont tear the paper up the wall
Q:I undid the P trap under my bathroom sink to clear a clog and now when I put the whole thing back together it leaks out of the top of the slip joint that connects the down pipe from the sink drain to the j-pipe. The down pipe is 1 - 1/4 and the j-pipe is 1-1/2 and I am using the correct reducer gasket. It was not leaking (and never had) before I took it apart. I have tried using a new gasket and teflon tape on the threads of the slip joint to no avail. Please give me some idea as to what the problem might be. Here is a link to a couple of pictures to show the general set-up and the specific problem: http://www.flickr /photos/sesquilia/?saved=1Thanks to anyone that can help.
Bathroom Sink Trap
We have produced the artistic glass washbasins earier in the country ,and leading style design trend ,driven by the development of the industry.

1. Manufacturer Overview

Location Foshan,China
Year Established 2006
Annual Output Value Above RMB5 Million
Main Markets Europe and the United States, Australia, Japan, South Korea

Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port Guangzhou
Export Percentage
No.of Employees in Trade Department 1 People
Language Spoken: English;Chinese;
b)Factory Information  
Factory Size: Above 2,000 square meters
No. of Production Lines 2
Contract Manufacturing OEM Service Offered;Design Service Offered
Product Price Range Average

Send your message to us

This is not what you are looking for? Post Buying Request

Similar products

New products

Hot products


Related keywords