stainless steel pipe clamp supplier

Ref Price:
$0.03 / pc
Loading Port:
Qingdao
Payment Terms:
TT LC
Min Order Qty:
100 pcs pc
Supply Capability:
300000pcs Per Month pc/month
Inquire Now Customer Service

Contact us by

(1) WeChat
(2) Whatsapp: +8617190086776

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Usage: Pipe Clamp
Material: steel、matel;Galvanized iron ,stainles
Band width:3mm/20mm
Connection:welding
Model number:As your requirement
Structure:Swivel clamp
Certificate:ISO9001:2008
Feature:
1.Use the open internal and external circle structure,and with screw fixed.It is effectively to solve the problem that when small diameter solft tube connect the hared tube,it is easy appear dead angle,and liquid or gas leakage problem.Easy structure,Easy maked.
2.Edge is no burrfree,it is ability to prevent the tube damaged
3.By a efficiently hydrogen relief treatment,long-term use needn't to worry fracture and other problems
Surface: zinc plated Packaging
4.Accord with DIN3017 Standard.By 48 hours salt and fog test,it has a good corrosion resistance
5.By our last 48 hours elastic test,to insure a high strength mechanical properties.
6.Easy to fix.
Working Temp: -40 ℃ ~ 110 ℃
Size:3/8" 1/2" 3/4" 1" 1 1/4" 1 1/2" 2" 2 1/2
Structure: Suspension Clamp and so on On-time shipment and pre-shipment product quality safeguards clamp is mainly used in automobiles,tractors, ships, gasoline engine, and so on each kind of mechanical
device for oil, gas, hydraulic hose connector, various types of
rubber tube interface must join parts fastening.
Detail: plywood case ,pallets or any other package as buyer's requirements
Delivery Detail: about 20-30days

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Clamp type meter use
Usage method(1) mechanical zeroing is necessary before measurement(2) select the appropriate range, first select large, then select small range, or see the nameplate value estimation.(3) when the minimum range measurement is used and the reading is not obvious, the number of turns to be measured shall be measured by the number of turns in the center of the jaw, and the readings = indication value * range / full bias * turn number(4) when measuring, the wire should be placed in the center of the jaw and close the jaw so as to reduce the error.(5) after measuring, place the change-over switch at the most measuring range.
Q:A selection table clamp type table
1, before use, should read the instruction manual carefully, make clear whether it is communication or AC and DC dual-use.2, the measured voltage clamp meter shall not exceed the values marked on the ground, otherwise easy to cause the accident, or cause the risk of electric shock.3, you can only measure the current one conductor, the measured wire clamp should be placed in the center of the window, the window with all phase conductors can not measure.
Q:The power consumption of the same load, different power motors?
The current may be a little smaller, because the power consumption of the motor will be smaller in every respect. Both active and reactive power will be smaller.
Q:How to use the 266CLAMPMETER clamp multimeter
The wrench jaw will open, the prediction of the amount of wire in the middle, measurement, the measured wire should be placed in the middle of the jaw with jaw, face such as noise, should be re opening and closing time, still have the noise, should handle the joint surface, in order to make accurate readings. In addition, not at the same time around the two wires.
Q:How do you measure current?!
An electric current is a flow of electric charges. The magnitude of the current is called the current intensity. It refers to the amount of charge that passes through a cross section of the wire per unit time, and is called a ampere per second through a Coulomb amount of electricity (Ampere).
Q:Why is the air compressor leakage gap will open?
Check which parts of the internal and external machines are faulty. First, disconnect the inside and outside lines so that you can determine which part of the problem is.
Q:The reason that the phase current meter of the three-phase asynchronous motor is too low and the other two phases is normal is that it is too normal
It can also be used to measure the faults at the far end or the proximal end of each phase. If the current balance of each phase is unbalanced, the problem of eliminating the current transformer is the problem of the motor
Q:How to measure a zero line with a universal watch?
Right hand with the red pen were measured in the zero line or line, you write down the results of the 2 measurements, the small FireWire, zero line.
Q:How to measure the motor current with a multimeter?
Measurement of alternating current. The measuring method is the same as that of 1, but the gear should be switched to the AC gear. After the current measurement is completed, the red pen should be inserted back into the "V" hole.If the measuring range is enough, measure according to the above method. Does not recommend the use of multimeter with clamp current meter to measure the motor current recommendations. Safe and convenient.
Q:How can I measure the voltage and current with a clamp?
Clamp meter with digital display and pointer display, measuring about estimated range of the measured current, pay attention to the selection of range clamp meter, try to choose the appropriate range to reduce the error. In addition to the wire clamp in the middle of the jaw clamp meter, if the measured current is too small, can take the form of a plurality of winding wires, and then measure the value by the number of roots, but also take care not to measure the bare wire, so as to avoid the risk of electric shock. If we can measure the voltage clamp and other functions of the table, when measuring the current to pull out test. Furthermore, in the three-phase load, the line of the jaw clamp measures the current of the wire, and the two measuring current is the third. When measuring the current voltage clamp meter should note 1, the measured line is lower than the rated voltage of the current clamp meter; 2, measurement of high voltage transmission lines, to wear insulated gloves, wear insulated shoes, stood on the insulating pad; 3, to close not charged for jaw closing range; 4, in the measurement of resistance before the tested circuit must be completely discharged, and completely isolated from the power supply circuit; 5, if the test pen or power adapter to replace the damaged power, must have the same model and the same electrical specification test pen and power adapter; 6, the electric energy consumption as the battery indicator instructions, do not use instruments. If you don't use it for long time, remove the battery after storage; 7, not in high temperature, high humidity, flammable and explosive and electromagnetic field to store or use clamp meter; 8, please use a damp cloth or cleaner clamp meter shell, do not use friction or solvent; 9, the instrument when wet please, drying and storage.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range
客服
live chat