perforated metal strut c channel for sale
1.Professional manufacturer & exporter
Strut Channel System Information
Strut Channel System Provides;
High quality & reasonable Price, no need welding and punching, can use repeatedly, wide usage range, flexible for installation.
1. Standard thickness: 1.5mm, 2mm, 2.5mm,2.75mm, 3mm
2. Standard length: 2440mm, 3000mm, 5800mm, 6000mm
3. Standard size: 41*21, 41*25, 41*41,41*62,41*72,41*82
Other sizes be produced according to customer’s drawing.
- Q:What are the models of the intrinsically safe cables?
- The national standards and industry standards for mining cables are as follows: GB / T
- Q:TV shows no signal how to do with which remote control operation ah
- It is to be installed and Ming Tu, not concealed and dark laying.
- Q:Can an ant video camera connect with millet smart u sb socket?
- With a multimeter, test, or ask, install the elevator technician ah! Is the same ah, there is no difference ah
- Q:My home is 2.5 square aluminum, I would like to ask the maximum load of electricity a few kilowatts, thank you!
- Try to stand in the customer's position to think about! The The More for the customer profit! The So you will have a lot of repeat customers! The Is a word service to be in place! The
- Q:Can high - voltage cables and low - voltage cables be placed on the same cable trench?
- Layout: automatic fast manual is reasonable is the first automatic and then manually change the automatic layout you use PROTELDXP2004 right to hope to help you
- Q:What is the plastic trunking fixed on the tile wall
- Optical fiber patch panel out, there are two general usage . then photoelectric converter, commonly known as fiber optic transceivers. . access module (used on the switch)
- Q:What is the difference between a KVVR cable and an RVV cable?
- What is the meaning of the cable 3 * 1 * 0.8?
- Q:YJV-4 * 240 + 1 * 120 and YJV-4 * 50 + 1 * 25, the two cables to wear a DN150 of the steel pipe,
- You pick it up, in the joints to wear a hose up, after the wiring is completed. After the tape is good. And then put up the hose, hose at both ends of the wire with the tie, so that is not afraid of the wet shower. After the wiring head is connected, if the best iron soldering tin tin.
- Q:Cable bridge, each section of the seams, there is a copper wire compiled flat belt connected?
- 1. Set the cable well 2. Connect with the cable connector 3. Press the hydraulic clamp with the sleeve 4. Heat shrink tubing 5. wrap the high pressure cloth cloth 6. wrap the waterproof cloth
- Q:What are the requirements for the connection of steel conduits?
- Do not put the wire tube in the warm tube outside the benzene board if the impact of benzene flatness, you can put the place where the wire tube off the benzene board, and then covered with insulation film, in the floor warm tube. Wire tube as flat as possible vertical, the use of pvc tube, the corner with a spring simmer bend simmer bending, bending radius greater than or equal to the diameter of 6 ≥ d, do not simmer pure 90 degrees dead or the use of finished 90 degrees elbow. Each tube has two 90 degree elbows that can be changed later. If the original body has been buried in the best use of wire, because now can thread, then the future can also change the wire, the wire is not affected by the temperature, if the wire pipe on the floor heating pipe when the temperature rises, the wire conductivity decline. Good, such as the big city developers to the house to the tenants, the distribution is pre-embedded threading is good, the tenants in the decoration is only based on the decoration needs on the basis of the original increase or shift, small city developers to Save money, do not give the wire to wear, they are irresponsible. And these live to the tenants, the tenants to find some residential property designated most of the uneducated professional electrician, whatever the outcome can pass power. Must find a professional electrician, he will be based on the requirements of households, their own experience and professional skills reasonable distribution.
We are now engaged in expanding our business scope to the global market and wish to establish mutually beneficial and long-lasting relationships with importers from all over the world. We stick to the belief of "strictly abiding by contracts and keeping credit are key points to be successful and they will lead both ourselves and our customers to a better future".
1. Manufacturer Overview
|Annual Output Value
||US$10 Million - US$50 Million
2. Manufacturer Certificates
|a) Certification Name
3. Manufacturer Capability
||81% - 90%
|No.of Employees in Trade Department
||English, Chinese, Spanish
||3,000-5,000 square meters
|No. of Production Lines
||OEM Service Offered Design Service Offered Buyer Label Offered
|Product Price Range