Silicate Calcium exterior wall Board

Ref Price:
Loading Port:
China Main Port
Payment Terms:
TT OR LC
Min Order Qty:
-
Supply Capability:
-

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

Specifications

One high efficient and cheap building decoration material,which can be applied to partition block,ceiling and insulation etc.

Item

Category

Density  g/cm3

0.9-1.2

1.2-1.4

Bending Strength MPa ≥

e=5 6 8

10

13

e=10 12 15

8

10

e≥20

7

9

Screw pull-out strength  N/mm  ≥

75

80

Thermal Conductivity W/(m.k)

0.29

0.20

Moisture content    %    ≤

10

bulking factor  %    ≤

0.25

Non-combustibility

GB 8624 :1997Class A

Plate edge straightness  mm/mm

1

Plate edge vertical degree mm/mm

2


Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Living room to do silicon calcium board ceiling, whether need to put putty, brush latex paint?
need. Gypsum board ceiling not only need to put outside the putty. The first step: first have to fill the first seam, the gypsum board interface first fill the seam to scratch the gypsum sticky powder or patchwork; the second step: and then paste kraft paper or cloth. The third step and then putty putty, if the wipes of environmental putty do not need point anti-rust paint, and will not rust. But if the scraping bucket glue putty must be a point anti-rust paint, and if no point will be rusty. The fourth step: usually gypsum board after filling the general two lowest putty. Not recommended to scratch three times. Too thick but easy to fall out.
Q:Decoration problem: a calcium silicate board about how many customers want me to calculate the weight.
1 OKorder twitch high libel gambling gambling performance 220 * 2440 * 6 calcium silicate board normal weight in 22kg. 6 refers to the thickness of the ceiling now more than 5%, 5% is generally 18kg. Under the premise of fixed specifications, mainly depends on the bulk density. However, due to the manufacturers of different recipe technology, bulk density will be a little different. Please add points.
Q:What is the density of calcium silicate board and fiber reinforced calcium silicate board?
Calcium silicate board and fiber reinforced calcium silicate board is the same concept, the density from 0.85 to 1.5 range, mainly depends on customer requirements and production process. 1 what is called low-density calcium silicate board. Thickness and density is not related, however, in general, low-density calcium silicate board are relatively thick, generally more than 12mm. Because the density is low, the folding rate of calcium silicate board will be low, so it is not easy to cut off some of the knot strings.
Q:What kind of ceiling does the open kitchen do?
Chinese kitchen generally recommended with aluminum slab plate or plastic plate, the most important is practical.
Q:Calcium silicate board model specifications
Conventional specifications are 1220x2440 thickness is mainly to see your use of the situation
Q:Hello, may I ask your calcium silicate board fire and fire test report, fire level several, how much fire temperature?
Taiwan Rong building materials without asbestos fire calcium silicate board National fire building materials quality supervision and inspection center testing, safety performance of the highest fire safety up to 4 hours Fu Ding Dian Dian Cao Dian Dian Dian water, the detection of fire-resistant grade non-combustible A1 level. The maximum fire temperature can reach more than 600 degrees
Q:Fire board fire resistance limit of 3 hours?
No ... ... two hours have reached a level of fire resistance ... ...
Q:Calcium silicate board specifications
1220 * 2440 mother 1200 * 600 mother 603 * 603 mother 595 * 595 mother
Q:Double layer 12 mm thick calcium silicate board with what keel ceiling
With the main keel of 50 and the vice keel of 50. Anyway, you buy such a set on the line.
Q:Renovation process, the bathroom partition which wall material is better?
Toilet wall should be used (or processed to achieve) moisture-proof material, a good sound insulation performance; partition wall material requirements should be light, thin thickness, to adapt to the corresponding environmental requirements, drawn from local conditions. Wall can not afford to load-bearing role, only to separate the room and space of the wall, according to the different ways can be divided into block-type partition, vertical tendons, wall-type partition three categories. There are several kinds: light brick, glass tiles, glass, wood, gypsum board, new concrete slabs, ceramic plates, metal surface sandwich panels, etc., are also constantly developing innovation. Some of the non-waterproof material can be coated with a waterproof coating or past tile to enhance its water resistance. The reality is that the material is not expensive, expensive man. Plate prices from ten dollars to hundreds of dollars; and labor costs is basically two or three hundred. Therefore, according to local conditions to select the material process, improve production efficiency to save labor costs is the ultimate savings. If the project is large, through the factory production, on-site rapid installation can greatly reduce costs and improve competitiveness.

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range