Q:How do you apply double-sided adhesive tape?

7, in the printing process to clean the printing plate, should avoid cleaning solvents, contact tape, so as not to damage the tape;8 when the plate is removed from the tape, the angle between the plate and tape shall be no more than 90 degrees.9, the interface version of the place to stay 5mm or so, the use of 3M 1600 electrical insulation tape seal version of the effect is good, you can effectively avoid wiping the plate caused by the interface version of the resulting ink pollution, and very economical.10, double-sided adhesive over repeated use can produce overprint bad phenomenon, especially in the new situation, and used for a long time in registering are likely to happen.

Q:What is oily double-sided adhesive, oily double-sided adhesive, what are the uses?

Application: suitable for arc surface sticking, stamping and compound pasting. Widely used in clothing, shoes and hats, leather, bags, embroidery, posters, signs, envelopes, decorations, electronic products and household appliances, etc., the use of simple and convenient.

Q:What are the general use of double-sided tape?

They are widely used in leather, nameplate, stationery, electronics, automobile decoration, shoes, paper making, handicrafts, paste, positioning and so on. Hot melt double-sided adhesive mainly used in stickers, stationery, office and so on.

Q:The advantages and disadvantages of the mesh double sided adhesive tape, and the influence of the density of the mesh on the adhesive tape.

What material should be divided into mesh adhesive tape, the substrate is different, advantages and disadvantages are different, the main use is also different.

Q:The basic requirements, attached to the bottom surface of the base, a bottom surface with a permanent adhesive, affixed to the side of the desktop environment. When the base is fixed with double adhesive, another part is inserted in it, and the component is required to be picked up from the vertical direction (>=15N), and the base is firmly jointed with the table top. But when the base needs to be repositioned, it can not be too difficult to pull out, and it can not destroy the structure of double faced adhesive, thus shortening the service life

As is heavy positioned in the production process requires a short period of time, the basic level of adhesive tape can meet, if it is produced after the long time the frequent need to re positioning, now need a permanent adhesive, a heavy residue series tape repeatedly.

Q:The double-sided adhesive thickness 0.05~3mm, similar to A3, the A4 paper size? One by one?

As you mentioned, these specifications need to be customized, and the thickness is from the 0.05MM-3MM,

Q:What about double white, white and yellow?

The way, yellow than white slightly better, see if there is no color requirements, ah, double-sided tape manufacturers

Q:How to fill in the property when releasing adhesive tape?

Thickness, color, temperature, specifications, use, base material, almost on these

Q:The mirror is glued to the glass door with double adhesive tape. How can the mirror be removed?

This has not been used. I guess so, because it belongs to the organic solvent. Try it. The hairdryer can be taken down, but the residue is difficult to clean

Q:Will double face adhesive affect its stickiness in summer?

Check whether the edges of the double adhesive tape are adhered or not, and whether or not the bottom sheet is leaking of siliconDouble adhesive tape edge adhesion or some parts of the bottom sheet leakage of silicone oil, in the processing process will cause waste paper rupture, can not be normal production. Therefore, before processing, take a length of about 1 meters of self-adhesive materials, hand peeling, to see whether the edge or other parts of the smooth, uniform peeling of the parts. Usually, paper and paper edge bottom adhesion occurred in a roll coating adhesive material cutting volume, and generally occurs only in the outer layer of 7 meters to 10 meters, so the drum encountered double-sided tape cutting edge with adhesion, don't immediately assert that the whole roll of paper have this problem.Also note that stripping light weight tissues (such as 60g/m2 and 80g/m2 facial tissue) is more powerful than peeling off heavy paper, and the lighter the paper, the more tightly it feels. Because of this, sometimes, according to the customer's request to cut the shape of the customer's choice of double-sided tape, can not be completed at the regular processing speed.