Product Description:
PVC Blacklit Flex Banner, is ideal advertisment material, with characteristics of
1. High strength
2. Weather resistant
3. Waterproof
4. Self-cleaning
5. Good smoothness
6. Perfect printing ability
7. Best color fastness
8. Gloss or Matt available
9. Customer's requirement available
10. Anti flame is available
Typical specifications of PVC blacklit flex banner
Package: Each roll of PVC flex banner is wrapped with kraft paper or paper tube.
- Q:Maintenance time of the cushion on the roof of the building
- According to the "concrete structure construction quality acceptance criteria" provides:
Concrete should be poured within 12h after the completion of the concrete to be covered, and moisturizing conservation;
- Q:Is foam concrete suitable for use as a cushion?
- And then through the foaming machine pumping system for cast-in-place construction or mold forming, the formation of natural conservation with a large number of closed pores of the new lightweight insulation materials.
- Q:Basement floor mattress dry to what degree can do coil waterproof?
- Third, the membrane waterproof in the construction should first do the basement floor of the waterproof, and then the membrane along the basement floor continuous paste to the outer surface of the wall. Basement floor waterproofing first in the foundation pouring C10 concrete cushion, the thickness of about 100mm. And then paste the membrane, and then in the coil to wear 20 thick 1: 3 cement mortar, and finally pouring reinforced concrete floor. The outer surface of the wall first wip 20mm thick 1: 3 cement mortar, cold base oil, and then paste the membrane, the membrane should be stitched paste, adjacent coil lap width of not less than 100mm. The top of the coil should be higher than the maximum water level of about 500mm, the outer side of the brick wall.
- Q:How to build a fine stone concrete cushion?
- Reduce ground cracking, plus steel mesh.
Reinforced mesh, should be placed in the middle of the concrete, because the protective layer of concrete thick Fang generally only 5CM thickness, so the middle is the best.
- Q:Roof waterproof mattress should play the number of centimeters appropriate
- Roof leaking of the construction program:
1. Need to remove the previous waterproof, such as paint, coil, etc., if it is to do the mortar waterproof can not be eradicated.
- Q:The top floor made waterproof playing cushion layer of how to do
- Roof waterproofing can not use a single waterproof material, must be rigid and flexible combination of construction, flexible waterproof stretch is good, a little bit of settlement or deformation will not damage the waterproof layer. Rigid waterproof (ie mortar waterproofing agent) waterproof at the same time, can play a protective role, waterproof layer is not easy to be destroyed.
- Q:The cushion is usually in the housing which parts
- Cushion is generally at the base, looking for the use.
- Q:What is the difference between leveling and cushion?
- and only in the construction of the building at the bottom of the building, it is possible to use the relevant level of the cube, After the use of the underlying layer of the building, it is not exempt from the possibility of using leveling layer
- Q:Cushion, waterproof layer construction to do what information
- 2, bedding (bed course) refers to the structure below the grass-roots level. Its main role is to water, drainage, antifreeze to improve the grass-roots and soil-based working conditions, the water stability requirements are better. The cushion layer is a structural layer between the base layer and the soil base. When the soil quality is poor, it is used to improve the water stability of the soil base, improve the water stability and frost resistance of the pavement structure and disperse Load to reduce soil deformation.
- Q:Is the raft cushion waterproofing full of the cushion?
- As for the bottom of the bar thickness of the protective layer is generally 4cm, but if the basic floor of the concrete label is relatively high, the protective layer can be appropriately reduced.
1. Manufacturer Overview |
| Location |
Hubei,China |
| Year Established |
1990 |
| Annual Output Value |
Above US$100 Million |
| Main Markets |
|
| Company Certifications |
ISO9001 Certificate |
2. Manufacturer Certificates |
| a) Certification Name |
|
| Range |
|
| Reference |
|
| Validity Period |
|
3. Manufacturer Capability |
| a)Trade Capacity |
|
| Nearest Port |
Wuhan |
| Export Percentage |
31% - 40% |
| No.of Employees in Trade Department |
15 People |
| Language Spoken: |
English；Chinese |
| b)Factory Information |
|
| Factory Size: |
10,000 square meters |
| No. of Production Lines |
5 |
| Contract Manufacturing |
OEM Service Offered；Design Service Offered |
| Product Price Range |
High；Average |
