Q:Power cable in the cable tray is a single layer of laying, or can be stacked together with multi-layer laying?

1: hard drive power cord 2: hard disk data cable (CD-ROM data cable) 3: graphics cable cable (if your graphics card is dual 6PIN power supply interface, but your power supply is only a 6PIN power supply interface, then the root switch on the use of ) 4: hard disk data cable (optical drive data cable) 5: hard drive power cord two hard drive power lines were inserted mechanical hard disk and solid state hard drive, two data lines were inserted mechanical hard disk and solid state hard drive, graphics card power supply cable are generally not , Believe that your power supply supports dual 6PIN power supply interface.

Q:Seeking: cable tray 100cmx10cm bracket installation spacing requirements

cable bridge and electrical equipment cross, the gap between the distance of not less than 0

Q:Where is the cable tray used? Fire power plant, coal mine group? For example, civil construction sites, some of the high-rise buildings.

Because YJV22 can be buried, so when the tube casing with plastic or steel pipe is no provision. Generally in the outdoors is a concrete packet bellows, into the building with steel pipe, are designed according to soil soils may be. Indoor in addition to continuous cable with the outside, rarely use YJV22 through the tube, because it is less likely to damage by external forces.

Q:Does the weak and fire can share a cable tray?

Specific can not be sure, it is recommended that you in the billing system through the tax classification code input power gold fuzzy search, according to find out the content, select a description of the most can be.

Q:I am a salesman who sells a cable tray, how can I sell my product, and now it is so depressing

UPS ah, Taobao a lot. UPS is the battery, if not always power on the partition time to turn off the power, let it discharge, or affect the battery performance.

Q:5 4 * 95 + 1 * 75 cable should choose what size of the bridge

1. Set the cable well 2. Connect with the cable connector 3. Press the hydraulic clamp with the sleeve 4. Heat shrink tubing 5. wrap the high pressure cloth cloth 6. wrap the waterproof cloth

Q:What is the difference between a trough bridge and a tray tray?

Upstairs did not understand the meaning of the question. Wire access control box is to set the length of the. The general requirements of the length of the land is not very high, the distribution box is particularly evident, many building distribution boxes are casually put the point line where the spare. Instruments and equipment on the electrical control box is a very high demand. In the line, from the terminal to the outlet hole is generally between the zigzag, tie tie, the length of the reservation line is about 1.5 times the width of the control box (about). This can be convenient after the replacement of components, maintenance and so on. Wiring is not like land with a direct cable access, but there are related technical requirements, such as anti-corrosion, anti-corrosion, and so on.

Q:Will the metal cable tray installation of the boom or boom specifications is how the provisions! Such as how much of the bridge is equipped with a large boom, how much must use the boom

Insulation for PVC sheathed for PVC 22 is steel tape armored

Q:What are the specifications for cable tray installation? What should I pay attention to when installing?

Generally in the installation, there will be instructions, as long as the instructions to operate, the general is not wrong.

Q:What is the profit of the cable tray?

The positive contact is a rigid part with a cylindrical (round pin), square (square pin) or flat (insert) Positive contacts are generally made of brass and phosphor bronze The negative contact, the jack, is the key part of the contact pair It relies on the elastic structure to be elastically deformed when engaged with the pin to form a resilient force in close contact with the positive contact to complete the connection (Vertical groove), folding type (longitudinal slot, 9-shaped), box-shaped (square jack), the shape of the jack, As well as hyperbolic thread spring jack and so on Second, the shell, also known as shell (shell), is the car connector cover, it is built-in insulation mounting plate and pin to provide mechanical protection, and provide plug and socket when the alignment, and then the connector fixed To the device Third, the insulator, insulator is also often referred to as the car connector base (base) or mounting plate (insert), its role is to make the contact according to the required position and spacing, and to ensure that the contact between the contact and And the insulation between the shell Good insulation resistance, withstand voltage performance and ease of processing is the choice of insulation materials into the insulator of the basic requirements Annexes, annexes, annexes and annexes Structural accessories such as the collar, positioning keys, positioning pins, guide pins, connecting rings, cable clamps, seals, gaskets and so on Installation accessories such as screws, nuts, screws, coils and so on Accessories are mostly standard parts and common parts It is these four basic structural components to make the car connector can act as a bridge, stable operation