Machinery handrail
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
We are the largest aluminum profilemanufacture in
Material | Alloy Aluminum 6063,6061,6005,6082 or customer nominated |
Temper | T3, T4, T5, T6 and other |
Surface | Anodize, electrophoresis, powder coating, PVDF coating, etc. |
Colour | Any colour based on Standard Germany RAL Mark |
Length | Not more than 16 meters |
Good Package | Inner plastic film /outside carton/wooden pallets |
Payment Method | T/T, L/C, etc |
Delivery Time | Normally 2-4 weeks, Delivery time can be consulted. |
Press Machine | 500-12500 tons all together 93 press lines. |
Fabrication | 1. Marchinery, 2. Drilling; 3. Bending; 4. Cutting; 5. etc. |
Certificate | ISO/TS 16949,DNV,IRIS,CCS,AFA,etc. |
Dies | 1. Using our dies, no fee; |
2. Using customer drawing, opening dies, usually about 5~50 tons then the dies cost can be refunded. | |
3. Die cost is negotiable base on the order quantity | |
Capability | Annual output 800,000 tons |
- Q:I have used ab repair several times, each time with only three months and leakage of fluorine, hope you master generous with your criticism,
- Aluminum tube evaporator if not leak greatly, I have been using A&B glue + Gauze trap, the effect is quite good, do test pressure 2.5MPa can withstand.Best not to glue, time is not too long and bad, they also said that you repair is not good, from the leak to expand into the bell mouth, with 8 pairs of silk butt, economical and easy to use.10 cm 6 mm copper inserts 5 cm (with torch heating), then the vacuum side at the joints' three 'drop gum (similar to 502, but better than the 502), then AB wrapped in gauze dipped in the outer two or three layers can be.
- Q:How do aluminum pipes compare to HDPE pipes in terms of flexibility?
- In terms of flexibility, aluminum pipes are generally less flexible than HDPE pipes. HDPE pipes have a higher degree of flexibility, allowing them to bend and adapt to different angles and curves. Aluminum pipes, on the other hand, have limited flexibility and are more rigid in nature.
- Q:What causes aluminium tubes to peel and blacken?
- The phenomenon is common when the aluminum pipe is connected with other metals and has electrolyte flow. This is because the electrochemical reaction results in the formation of a galvanic cell. Aluminum is the anode, and the surface of the aluminum tube is oxidized to cause blackening and peeling
- Q:Are aluminum pipes suitable for outdoor applications?
- Yes, aluminum pipes are suitable for outdoor applications. Aluminum is highly resistant to corrosion, making it a durable option for outdoor use. It also has a high strength-to-weight ratio, making it easy to handle and transport for various outdoor projects. Additionally, aluminum pipes can withstand extreme weather conditions and temperature changes, further enhancing their suitability for outdoor applications.
- Q:Can aluminum pipes be used for geothermal heating systems?
- Indeed, geothermal heating systems can make use of aluminum pipes. The popularity of aluminum in the construction of geothermal heat exchangers is due to its remarkable heat transfer capabilities. With its high thermal conductivity, aluminum effectively transfers heat from the earth to the fluid flowing within the pipes. Moreover, aluminum is renowned for being lightweight, resistant to corrosion, and possessing a long lifespan, rendering it a durable and economical choice for geothermal heating systems. Nevertheless, it is crucial to insulate the aluminum pipes appropriately to minimize heat loss and optimize the system's efficiency.
- Q:1100 what is the difference between the aluminum tube and the 6063 material aluminum tube, please advise
- The 1100 is rust proof aluminum grades, good corrosion resistance, good plasticity, but the intensity is the lowest, 6063 forging Aluminum Alloy, is Aluminum Alloy, if after solid solution treatment and aging, high strength and hardness, but the corrosion resistance of less than 1100,
- Q:Can aluminum pipes be used for high-pressure applications?
- Yes, aluminum pipes can be used for high-pressure applications. Aluminum is a lightweight, durable, and corrosion-resistant material, making it suitable for various industries and applications, including high-pressure systems. However, the specific pressure rating of an aluminum pipe depends on its size, wall thickness, and alloy composition. It is important to consult industry standards and guidelines, as well as engineering professionals, to ensure that the chosen aluminum pipe is suitable for the intended high-pressure application.
- Q:I do not know compared with copper tube, durable, long time will appear trachoma?
- So we need to use it properly:Do not strike or defrost with sharp or hard material to prevent damage.Not special circumstances, long-term use of the refrigerator, because it is covered with a layer of ice can be isolated from the air to prevent oxidation.Put the refrigerator in a dry and airy place.
- Q:Are aluminum pipes suitable for structural supports in buildings?
- Aluminum pipes can be suitable for structural supports in buildings under certain circumstances. Aluminum is a lightweight material, making it an attractive option for construction projects that require ease of handling and installation. Additionally, aluminum pipes are resistant to corrosion, which can be advantageous in environments with high humidity or exposure to chemicals. However, it is important to consider the load-bearing requirements of the building when choosing aluminum pipes as structural supports. Aluminum has a lower strength-to-weight ratio compared to other materials such as steel, which means it may not be suitable for heavy loads or applications that require significant structural support. In such cases, steel or other stronger materials would be more appropriate. Furthermore, aluminum pipes may be more susceptible to deformation or bending under heavy loads or extreme weather conditions. This can compromise the structural integrity of the building if not properly accounted for in the design and construction process. Ultimately, the decision to use aluminum pipes as structural supports in buildings should be based on a thorough analysis of the specific project requirements, load-bearing considerations, and consultation with structural engineers or experts in the field.
- Q:Are aluminum pipes suitable for underground installations?
- Aluminum pipes, indeed, prove to be a fitting choice for underground installations. Their versatility and durability make them an ideal material for such applications. To begin with, aluminum pipes possess a lightweight quality that simplifies their handling and installation when compared to materials like steel or cast iron. This attribute not only reduces transportation expenses but also minimizes the requirement for heavy machinery during the installation process. Moreover, aluminum exhibits exceptional resistance to corrosion. It forms a natural protective oxide layer on its surface, rendering it highly impervious to rust and other forms of corrosion. This reliability makes aluminum pipes an excellent option for underground installations, where they will be subjected to moisture and varying soil conditions. Furthermore, aluminum is non-magnetic, making it appropriate for underground installations in areas where magnetic interference might be a concern, such as in close proximity to power lines or sensitive electronic equipment. Additionally, aluminum pipes possess commendable thermal conductivity, facilitating efficient heat transfer. This proves beneficial for specific underground applications like geothermal systems or underground heating and cooling pipes. However, it is crucial to note that aluminum pipes may not be suitable for every underground installation. Factors like soil conditions, water chemistry, and the presence of corrosive elements should be taken into account before selecting aluminum as the material for underground pipes. It is advisable to consult with a professional engineer or contractor experienced in underground installations to ensure the appropriateness of aluminum pipes for a specific project.
1. Manufacturer Overview |
|
---|---|
Location | |
Year Established | |
Annual Output Value | |
Main Markets | |
Company Certifications |
2. Manufacturer Certificates |
|
---|---|
a) Certification Name | |
Range | |
Reference | |
Validity Period |
3. Manufacturer Capability |
|
---|---|
a)Trade Capacity | |
Nearest Port | |
Export Percentage | |
No.of Employees in Trade Department | |
Language Spoken: | |
b)Factory Information | |
Factory Size: | |
No. of Production Lines | |
Contract Manufacturing | |
Product Price Range |
Send your message to us
Machinery handrail
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
Related keywords