Q:Can the inlet and outlet of butterfly valve be reversed? Why? What will happen if the reverse gear is installed?

Our factory butterfly valve has two-way sealing, can be installed, and will not leak. If there is an arrow above the butterfly valve is one-way seal, that is, can not be installed. One way sealing will cause leakage. If you have any other questions, you can bring them up. Let me help you with that

Q:What do D71, D371 and D341 represent in butterfly valves?

D71 in D is the meaning of butterfly valve, 7 refers to the connection is the clamp, and 1 refers to the butterfly plate is the center of verticalD371 in D is the meaning of butterfly valve, 3 refers to the drive mode is the turbine, 7 refers to the connection is the clamp, and 1 refers to the butterfly plate is the center of verticalD341 in D is the meaning of butterfly valve, 3 refers to the drive is turbine, 4 refers to the connection is flange connection, and 1 refers to the butterfly plate is the center of vertical. China valve Holding Group Co., Ltd. Zhang Chao 021-55601036 Fax: 021-66289822

Q:What type of valve does the butterfly valve D343X DN300 represent?

D- butterfly valve, 3- worm drive, 4- flange connection, 3- three eccentric, X- soft seal, DN300- nominal size is 300, the full name is 300 of the three eccentric butterfly valve, and I hope to help you.

Q:The difference between vertical and horizontal butterfly valves in municipal water supply

The general municipal water supply butterfly valve is mainly vertical installation, mainly due to underground pipe network, vertical drive device in the upper, easy to operate, and installation of smaller wells;Horizontal, usually large diameter butterfly valve, usually used in the main network, often open, not easy to collect slag.

Q:D37A1X9-16CB1: what does this butterfly valve mean?

The model is composed of 7 units, the types of valves (gate valve Z, J, L, Q ball valve, throttle valve, check valve and H valve, butterfly valve, connection mode (D) internal thread 1 thread 2, welding flange 4, 6, 7, the clamp (0) electromagnetic transmission mode 1 solenoid valve, hydraulic, electric and hydraulic turbine are 2, 3, 4 and 5 gears, bevel gear, pneumatic hydraulic, 6, 7, 8, 9) pneumatic and hydraulic, electric, structure (straight or DC type 7,1 on behalf of the center plate, vertical type A (A) and LT X9) on behalf of a sealant is heat-resistant rubber, kg 16 kg, C represents the body material of carbon steel WCB, B1 on behalf of the valve plate is made of ductile cast iron plating)

Q:I have a 1993 Oldsmobile Cutlass Supreme and I think I have the case of the blow-by. The engine had high mileage, but was rebuilt b/c it stalled while driving. 3.1L V6 gasoline engine. The fuel filter and the fuel pump are brand new. Now we have the same problem a few months later. It stalls while driving. Its been sitting a while and won't start by itself, so I pulled off the air intake hose off of the air filter to spray starting fluid into it. I noticed oil puddled in the air intake hose, so I looked for the PCV valve on the rocker cover. There is a tube going from the air-intake hose to the rocker cover. I popped out the tube from the rocker cover and there is no PCV valve. Just tube. Is that where the PCV valve is supposed to go? If not, where can I find it on the engine? And could that possibly fix the blow-by and the stalling engine? I'd appreciate any help. Thanks in advance.

top of the manifold

Q:Butterfly D371X5-16ZB1 what does each letter stand for?

Daily valve pressThe regular model is out of step with you. I can only explain the regularD371X5-16ZB1D is butterfly valve3 is the turbine drive7 is the clamp connection1 is the display opening signX is a rubber seal16 is 16 kg pressureI don't know the other superfluous letters

Q:My bike has now 6200 miles on the odometer. The manual says that a valve adjustment should be performed every 6000 miles. But the bike runs fine. Can I just have the valve checked or should I have them adjusted even though the bike is fine? What will happen if I just keep riding it?

First off you are suppose to take your bike back to have your valves adjusted after 500 miles. Anything later can cause problems. The motor is already broken in. why did you wait so long to have them adjusted ? Your vibration is the tire is not balanced right , take it else where. good luck

Q:Which is expensive, butterfly valve?

Butterfly valve is more common, less material and simple structure. Butterfly valve cheaper

Q:How can I get the fire signal butterfly valve?

1, the signal butterfly drive by the worm gear drive shaft and butterfly plate rotation, realize the opening and closing and control flow. 2, rotating the handwheel worm gear to the disc to open and close and adjust the flow to the handwheel clockwise rotation for the valve closed. 3, worm gear is arranged in the box body micro switch has two forms: A, in the gear box body is provided with open and close direction two microswitches, respectively, when the valve fully open and close action, connected to the control room "valve open" valve off "light source, the quasi it shows the state of the valve switch. B, in the driving device is arranged in the box body the microswitch (disc position close to 0 degrees), when the butterfly plate from 0 degrees to 40 degrees when the position of a micro switch, the output valve closed signal, 40 degrees to 90 degrees when the position of another pair of normally closed output valve opening signal. A cam that adjusts the touch microswitch and shows the different positions of the disc.