knife seat，F-KB001 acacia wood&glass knife seat
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
You Might Also Like
MEAS：20*23*8.5cm
Key Specifications/Special Features:
Size can be customized
Can print your design of packing
Various styles for choice
Can print your design of packing
Small quantity order is accepted
We also have bamboo and plastic cutting board for choice
Our advantages:
All of our products are made by our experienced team of hard working artisans in a safe and responsible environment.
We take great pride not only in the outstanding quality of our products but also in the environment in which they are made
Every product that bears our name was made in an ethically and socially responsible way
Treated by high temperature, making our product antibacterial
Easy to clean, much durable and harder than other board due to the good material
Primary Competitive Advantages:
Brand-name Parts Country of Origin
Distributorships Offered Experienced Staff
Form A Green Product
Guarantee/Warranty International Approvals
Packaging Price
Product Features Product Performance
Prompt Delivery
- Q:What are the reasons for the deviation of the CNC lathe tool holder after each turn
- One can not ignore it, not too much on the image processing, if it is the second case, the same is change the knife knife position error, the method of 1 open open turret encoder is damaged, replacement of damaged encoder.
- Q:How to return to the ordinary lathe tool
- Remove and check whether the spring pin back position is smooth (with the hands of the press about 20 times). Take a look at whether the end of the spring pin has been seriously worn, the same knife bottom surface is also turned over to see if the limit groove is also serious wear. Wear badly needed to repair or replace.
- Q:To the signal line where the pull resistance, pull resistance to do with the trouble to say clearly?
- In a word: your signal circuit IC no internal resistance, protection. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. Pull on the device is the injection current, the output current is down; just pull the weak and strong resistance, no strict distinction between what; for non (collector or drain) open circuit output circuit (such as gates) current and voltage capacity improvement is limited, the pull-up resistor is the main function of open circuit output type of circuit output current for the collector channel. All the pull-down resistor pull-up resistor is used in logic circuit, the circuit current is very small, the logic circuit of MOS tube bias current is microampere, even pA uA, the current level to provide a desired level, such as the current level without any output, because there is a pullup resistor so after a level is actually connected to a high level. Power amplifier circuit with no pull down resistor. Pull the signal is determined by a high resistance resistor at the high level, while the resistance from the current limit, pull the same. The pull-up resistor is the main function of the open circuit output current output channel for the collector; main function is connected with the pull-down resistor resistor together to line in the closed circuit driver (node) to a fixed level. Pull on the device is the injection current, the output current is down to note is that the pull-up resistance caused by too large delay output level, including the choice of the principle of resistance: 1, from the current irrigation ability to save the power consumption and chip considerations should be large enough; resistance...
- Q:Oblique bed CNC lathe in the row on the turret mounted electric turret, and then install the power head, you can also install the tailstock, I do not know this? Cheap not?
- It seems that the tail frame can not be installed, loaded up is not much significance other can be installed at least 120 thousand or more
- Q:How to use the left side of the knife knife thread?
- With the right angle, X write positive, and with the left deflection angle, the value of X to write negative. Because the coordinates are opposite
- Q:The cutting surface of the optical fiber cutter is like this, what's going on?
- The blade is high, it is recommended to turn down a little.
- Q:CNC lathe tool holder can not be reset after the knife to do?
- If it is not normal because hit the reset knife out of data (control board NC normal output but blocking of the motor so cause can not be restored to the original position), this is the best of the carriage return the mechanical origin of the data after reset (reset)
- Q:What is a tray roll bag
- Super large PE bag (tray bag, tray roll bag, super PE even roll bag): for the industrial production of super large PE bag, super PE roll bag.The utility model is mainly used for the packing of the pallet goods, various Super machinery, the packing of the goods, and the waterproof leakage proof of the swimming pool and the related buildings. Available for various specifications, various forms of super Dalian roll bag. The work efficiency is effectively improved, and the labor intensity is lightened.Material; PE, aluminized film, shrink film, etc. can be produced according to customer requirements. Maximum size; 8m/36m bag shape; top opening, side opening, m side, etc..
- Q:The direction of the tool head and the tool head of the NC lathe
- G41g42 use the judgment of the tool tip is not the same as you this figure to 09 knife point for the center of the rotation of 180 degrees is the rear tool head position input value evaluation standard front and rear is the same as the input value
- Q:What is the difference between the KSJ and HV
- Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
knife seat，F-KB001 acacia wood&glass knife seat
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
Quality Product, Order Online Tracking, Timely Delivery
OKorder Financial Service
Credit Rating, Credit Services, Credit Purchasing
Similar products
New products
Hot products
Related keywords
