Q:If you put clay over wire and bake it would the wire melt and ruin the sculpture?Details on wire:I'm not sure what kind of wire it is but it says Bright Floral Wire..Wire is silverDetails on Clay:Again, im not sure what clay...its from polyform products and it says Premo Sculpey so im guessing Polymer? :#92;Clay is Black.Bakes for 275F (130C)30 minutes per/par/por1/4 in (6mm)

Copper Chicken Wire

Q:like lets i want to want to connect my speaker wires with other wires can i use elmer glue so that it sticks and will the wires still work?

u have to take off some of the plastic parts then twist the wires together then put electrical tape.. well atleast thats how i think it's done..

Q:I just installed a backup camera however I am having trouble wiring it. I've read that I need to tap into the reverse wire, however I went through many wires and couldn't figure out which one is it. My cameras wire is designed to be wired in the trunk, so the wire under the hood or dash is not a possibility. 2003 G35 Sedan

For the objective of? turning it on? NO! you should use that wire, faucet it for sure, with a speedy connect, for a 12V source wire, use a relay, and that 12V source wire, and that is advisable to do 2 body grounds, one for that 12V source wire for the relay to kick on/off, and one from the digital camera that you're powering from a right away link from the battery (use a 10A inline fuse)

Q:I dont understand it I am trying to get a 1ohm load on a 2ohm dvc speaker but cant figure out how to tell if the wire you connect in the postive terminal on the sub in a neg wire or positive how do you tell what the gray line is on this diagram positive or negetive and how to tell. thanks

the wire (s) should be either silver or Gold Or 1 solid color wire 1 wire with a stripe

Q:I'm trying to install a ceiling fan and I'm looking for some help given my home's wiring. I have a single light switch in the room, and here's what's coming out of the ceiling: 2 white wires, 2 black wires and a ground wire. It seems like a set of white and black originate from the same location (in both cases). My celing fan with light has a remote connection, so there's one black, one white and one ground wire coming from my fan to connect to the ceiling. Can someone let me know how to hook it up so the fan and light both work? Thanks in advance.

In most cases in would be all blacks and all white and grounds together...........but some electricions will take heat back to the switch on the white leg............if they switched wires you can tell by opening the switch box and look at the colors..........try a light bulb first..........to see what switches it. Nothing to it..........just look........you'll get it.......also you will find if it's been changed......normally a white wire will have a black piece of tape around it...........that's telling you that white leg is now black and going to be hot . nite

Q:01 F350 that did not come factory with cab lights.Bought the recon cab lights that come with its own harness. No plugs on the ends, just plain wires on the end. Where does the green wire splice in to behind the passenger kick panel?

if a 2 wire loom, black is ground and green would be park lamps. get a test light, ground one end and stab wires until you find the live wire that lites the test lite. park lamp switch must be on when testing. head lamp switch 1 click out.

Q:I am building an ice chest boombox and want to wire a toggle (on/off) switch to turn the amp on and off....the amp is wired directly to the battery....my question is that I am using 6 gauge wire....but can't find any female spade connectors that are 6 or even 4 gauge to hook to the terminals on the switch.....what is a simple way to do this....am I going to have to solder the wire straight to the terminals?

Why not wire the toggle switch into the remote + wire? The one that turns the amp on and off with the head unit. 7/5/2013**** Leave the power supply wire alone. The thick 4 gauge wire that runs from the battery directly to the amp, leave it alone, don't put a toggle switch inline on that wire. Instead there's a wire from your head unit (or ignition) that runs to your amp, it turns on the amp when the head unit turns on or your ignition key is in the on position. It's usually 16 or 14 gauge. That's the wire where the toggle switch belongs. Look at your amp, this wire I am speaking of is probably labeled remote+ or ign or something like that and it's usually located next to your power and ground connections on the amp.

Q:I'm trying to install a ceiling fan but I'm having trouble with the wiring. Coming out of the fan I've got a black, white, black and white striped, and a green wire. coming out of the cieling i've got a black, a white and a red wire.The fan's green wire is connected to the bracket as a ground, so that's out of the way. It's the other wires that confuse me. I've tried, white to white, black to black, and BW striped to red, but that didn't do anything.Any ideas? Thanks.

You would need a meter to check those wires coming out of the ceiling...usually 3 wire cable (black, red, and white) are used for a 3 way switch which can be turned on and off at 2 separate location (example:at both ends of a staircase)..If this is your situation, you will need only 2 wire cable (black and white) on a switch..you didn't mention whether you have a lighted fan or not..If so, the black w/white stripe would be for the light...just one more thing, make sure your room switch is on when testing it...

Q:i have a 2002 hyundai sonata and i need to find a wiring diagram but i cant find it at all, please help

Car Radio Battery Constant 12v+ Wire: Orange Car Radio Accessory Switched 12v+ Wire: Yellow Car Radio Ground Wire: Black Left Front Speaker Positive Wire (+): Brown/White Left Front Speaker Negative Wire (-): Black/White Right Front Speaker Positive Wire (+): Brown/Yellow Right Front Speaker Negative Wire (-): Black/Yellow Left Rear Speaker Positive Wire (+): Brown/Red Left Rear Speaker Negative Wire (-): Black/Red Right Rear Speaker Positive Wire (+): Brown/White Right Rear Speaker Negative Wire (-): Black/White

Q:I have two DVC subs and I know how to wire them down to 1 ohm with the wires coming out of one outlet on the box but I don't know how to wire them down to 1 ohm with wires coming out of both sides of the box. Anyone have a wiring diagram for this?

Well, okorder /...