Q:There are several kinds of tape knowledge

1, tape according to its efficacy can be divided into:High temperature adhesive tape, double sided adhesive tape, insulating tape, special textured paper - pressure sensitive textured paper,Die cutting tape, anti-static tape, anti-static warning tape, different effects, suitable

Q:How do you apply double-sided adhesive tape?

7, in the printing process to clean the printing plate, should avoid cleaning solvents, contact tape, so as not to damage the tape;8 when the plate is removed from the tape, the angle between the plate and tape shall be no more than 90 degrees.9, the interface version of the place to stay 5mm or so, the use of 3M 1600 electrical insulation tape seal version of the effect is good, you can effectively avoid wiping the plate caused by the interface version of the resulting ink pollution, and very economical.10, double-sided adhesive over repeated use can produce overprint bad phenomenon, especially in the new situation, and used for a long time in registering are likely to happen.

Q:How to remove double adhesive on paper?

Get some petrol at the glue point. Or put ice in the refrigerator after the trial, try not.

Q:Double sided tape how to cut well, master with automatic cutting table, cut out, all askew, what reason, what should pay attention to?

Two, aspects of the tape of the material itself may be a problem, some of the material almost cut when the effect is not too good, will play a flash, or volume, complex will also affect the cutting effect, to spread the trouble, in addition, mechanical equipment has great influence, we are do the cutting device, cutting time, feed speed is that, because the first two are no problem, good automatic cut several section of cutting speed, feed, cutting, cutting paper and so on, if not cut it, only one speed in, too may the flash, uneven cut

Q:The basic requirements, attached to the bottom surface of the base, a bottom surface with a permanent adhesive, affixed to the side of the desktop environment. When the base is fixed with double adhesive, another part is inserted in it, and the component is required to be picked up from the vertical direction (>=15N), and the base is firmly jointed with the table top. But when the base needs to be repositioned, it can not be too difficult to pull out, and it can not destroy the structure of double faced adhesive, thus shortening the service life

As is heavy positioned in the production process requires a short period of time, the basic level of adhesive tape can meet, if it is produced after the long time the frequent need to re positioning, now need a permanent adhesive, a heavy residue series tape repeatedly.

Q:What's the material of PE foam double release tape? Urgently!!

Is from the type of paper or film or paper is paper? Gerasin coated silicon film, release film is called red film green film, the material is PE.

Q:With scissors to cut the foam double-sided tape, the scissors left a foam glue, sticky extra strong, difficult to remove, what is the way to remove the residual foam on the scissors?

First, use wire ballTools / raw materials: steel wire balls (for washing dishes, washing dishes) and dishwashing detergent.Methods / steps:1. Bring out the scissors glued to the glue, dip the water into the wet scissors, and apply the detergent;2. Brush with steel wire brush;3, clean water on a clean.

Q:How to separate water-based double-sided adhesive and oily double-sided adhesive?

Hot melt double-sided adhesive mainly used in stickers, stationery, office and so on. Oily double-sided adhesive, mainly used in leather goods, pearl cotton, sponge, shoes products, such as high viscosity. Embroidery double-sided adhesive mainly used in computer embroidery

Q:How to fill in the property when releasing adhesive tape?

Hello! At present, there are many kinds of adhesive tape on the market (such as sealing tape, printing adhesive tape, double sided adhesive tape and stationery tape,

Q:The door frame is glued on both sides of the curtain. Now the curtain doesn't work. It can't be cleaned on both sides. How can it be removed? But it doesn't break the paint on the door It's a little bit on the wall, too.

3, and so on 5 minutes later, with a dry cloth to wipe, you can quickly get rid of.4, if you still feel a little sticky, just do it again in the same way.