HDPE pipe extrusion line/HDPE pipe production line/plastic pipe extrusion line

Ref Price:
Loading Port:
Shanghai
Payment Terms:
TT OR LC
Min Order Qty:
1 set
Supply Capability:
10 set/month

OKorder Service Pledge

Quality Product

Order On-line Tracking

Timely Delivery

OKorder Service Pledge

Credit Rating

Credit Services

Credit Purchasing

Share to:

Product Description:

HDPE pipe extrusion line/HDPE pipe production line/plastic pipe extrusion line

Introduction

The screw of the extruder equipped with barrier unit and mixing structure, and the barrel owns new style grooves. All of these offer good plastification and mixing effect. Special design of basket die head of for HDPE(PP,ABS) large diameter pipe with thick wall offer lower melting temperature, good mixing, lower pressure of cavity ,and stable production.

Special design for sizing and cooling system by using film and water ring to cool HDPE(PP,ABS)material, which can fit for the requirement of HDPE(PP,ABS).And the design can ensure the stability of diameter and roundness when producing the pipe with thick wall.

Special design vacuum sizing tank can ensure the stability of size and roundness, Speed controllers are used in extruder, haul-off to offer stability and precision.

The whole line adopts PLC control system and large liquid crystal screen, which makes the operation very convenient. The line can be equipped with another extruder used for extruding the mark line.

 

Detailed Product Description

1.single screw extruder, very suitable to process PE resin with high capacity, max capacity  1000kg/h

2.The production line adopts reasonable design, absorbing safe producing technology, acquiring CE certificate.

3.Diameter range is 16mm-800mm, which can be changed into inch standard to meet clients special requirement.

 

Technical data

Pipe range

16-63mm

20-110mm

75-160mm

90-250mm

110-315mm

160-450mm

315-630mm

500-800mm

Extruder

¢45mm

¢60mm

¢75mm

¢75mm

¢90mm

¢90mm

¢120mm

¢150mm

Extruder power

AC30kw

DC75kw

DC110kw

DC110kw

DC160kw

DC160kw

DC280kw

DC335kw

Extrusion  capacity

60-100kg

100-150kg

250-300kg

250-300kg

350-400kg

350-400kg

650-700kg

850-900kg

Max. Production speed

10m/min

6m/min

6 m/min

6 m/min

3 m/min

1.2m/min

.9m/min

0.7m/min

 

Send a message to us:

Remaining: 4000 characters

- Self introduction

- Required specifications

- Inquire about price/MOQ

Q:Cable extrusion machine 6.57090 machine model how to see, know the master to say, thank you
Cable extruder type 657090 machine, describes the diameter of the screw, the unit is mm.The greater the number, the greater the equipment, the greater the amount of gumIt is usually marked on the control cabinet of the equipment
Q:What is an extruder?
Coextrusion is divided into two color co extrusion and hard and soft coextrusion.
Q:PVC jacket material in the production of fiber optic cable products,
Or the outer lubrication part of low molecular weight is replaced by macromolecule lubrication
Q:Where is the Huangyan extruder machine?
You want to see what type of mold processing, but Masino comprehensive, injection mold, blow mold, mold and so on can be developed.
Q:What is the adjustment method of China's extrusion machine die?
(3) line to die: suitable for small section of wire and cable adjustment. Pass the wire through the mold core, connect to the traction line, then run the glue and fine tune it. When the glue is running, adjust the screw and the traction speed, start the car, take the line sampling, and then stop to observe the thickness of the plastic layer of the sample is even, repeated several times until the tune until so, and then tighten the screws
Q:How to adjust the 65 screw gap in the extruder?
This should be practical learning. The outlet plane of the barrel is about 3 mm in diameter.
Q:Basic parameters of extruder screw
1, screw diameter Ds screw diameter is the diameter of the thread, the extruder production capacity (extrusion amount) is approximately proportional to the square of the diameter of the screw and, under the same other conditions, the screw diameter increases a little, significant increase will cause extrusion amount, the effect was even greater than the effect of the increase of screw speed on the extrusion rate is high. Therefore, the screw diameter is used to characterize the specifications of the extruder.
Q:What are the components of an extruder?
An extruder in which an air vent is disposed at the center of an exhaust extruder to allow removal of air and volatiles from the processed plastic. The main machine of plastic extruder is plastic extruderIt consists of an extrusion system, a drive system and a heating and cooling system. 1. extrusion system extrusion system includes screw, cylinder extrusion die head, extrusion die head, molding parts of the extruder. Also known as extrusion die, extrusion die. The utility model has the function that the plastic melt from the extruder barrel is well distributed in the die runner so as to be extruded and formed from the die at a uniform speed. The forming action of an extrusion die is in the process of complete extrusion (see plastics processing). A plastic extruder consists of an extrusion system, a drive system and a heating and cooling system. The classification system of extrusion system includes 1. extrusion screw, barrel, hopper, head, and mould, plastic extrusion system by plasticizing evenly into the melt, the establishment of Liu Hesheng basic information name in this process and Liu Hesheng taught: - professional engineeringControl science and EngineeringJob: in gender: Male College: College of mechanical and power engineering representative paper: melt rotating twin screw extruder in conveying flow solving teaching: research direction: mainly engaged in polymer material processingLinear low density polyethylene (LLDPE) linear low density polyethylene (LLDPE) linear low density polyethylene is structurally different from the generallow density polyethylene
Q:What impact does the extruder vacuum pump open or close on the extrusion product?
If the vacuum pump does not open, it may cause bubbles in the extruded product.
Q:Does anyone know the operating procedures for the cable 65+120 extruder?
What are the operating specifications for the extruder?One is the equipment instructionTwo is the boot operation specificationsThree is safety instructions and so onThe equipment manufacturer will provide the above

1. Manufacturer Overview

Location
Year Established
Annual Output Value
Main Markets
Company Certifications

2. Manufacturer Certificates

a) Certification Name  
Range  
Reference  
Validity Period  

3. Manufacturer Capability

a)Trade Capacity  
Nearest Port
Export Percentage
No.of Employees in Trade Department
Language Spoken:
b)Factory Information  
Factory Size:
No. of Production Lines
Contract Manufacturing
Product Price Range