Q:How do we calculate the cost?

Four major matters needing attention in investment of recycled plasticsPlastic recycling is a sunrise industry, the country, not only the effective utilization of resources and protect the environment, reduce the white pollution, from 2004 recycled plastics market, considerable benefits, as a new way of friends, is the author contact situation (editor's note), there are many aspects should be prepared in the first period, not to fight the battle without. The main problems are concentrated in the following aspects:1, blind follow-upAccording to the renewable materials market in 2004 prices, had been recycled most of the people have a better income, as for friends, in the test stage, on the surface has the advantages of simple process, low equipment investment, the product basically in short supply, technology content is not high, ordinary people can do at the same time, the raw material is us around the most familiar things, everywhere, everywhere can buy. Rough calculation, such as waste 2000 yuan can receive, the product can sell 4000 yuan, absolutely profitable.

Q:What are the requirements of customers for nylon plastic products?

Nylon engineering plastics products as the largest and most important varieties, has very strong vitality, mainly because it is modified to achieve high performance, followed by cars, electrical appliances, communications, electronics, machinery and other industries of high performance products are more strongly. The rapid development of related industries, promote high performance engineering the process of plastic, nylon future development trend are as follows.

Q:Laizhou plastic processing plastic machinery and equipment, which is more reliable, relatively good?

In contrast to many manufacturers of plastic processing equipment, more important is environmental protection, there is calm in the future, if you want to buy the equipment you can go to Laizhou city to take a look at the field, there are a lot of home doing well, you have this problem too vague, but also do not know you to play some bottom in figure what product, change a problem to try again

Q:where there are advanced environment-friendly recycled plastic processing equipment?

Environmental protection recycling plant, this is a systematic project, the use of granulation machine is usually used granulator, need to be matched with waste water filtration, sedimentation, purification treatment pond, waste gas purification equipment.

Q:profit is not big, about how much investment, please expert advice, mainly to supply the market and small supermarkets

I just do this, the raw material is used PE, equipment, there are mainly blowing machine, punching machine, if you want to print, then also the printing press, there are other stirring what ah!

Q:Which kind is with a lid, hollow, a little like PP material, white is a little transparent. It used to be filled with oil or wine. How is it processed? What company has custom-made?. Need to make the tank.

The plastic oil tank has the characteristics of light weight, corrosion resistance, shock resistance, no explosion when it is burning, high safety, high structural design freedom, high space utilization, etc.. However, the ordinary HDPE fuel tank has poor barrier to gasoline, and the leakage of fuel is larger.Fluoride treatment technology of plastic fuel tank to improve the vehicles, as well as a variety of general machinery (such as lawn garden machinery) provides a new solution to the fuel system of volatiles emission pollution. The surface of the tank is treated by fluorination technology, which can greatly increase the amount of fuel evaporation and infiltration, reduce the pollution to the environment, and meet the more stringent emission standards. At present, the fluorinated fuel tank has been widely used in the automotive industry in europe. In California, the United States will soon implement a pollutant control plan for small general-purpose machinery, and also consider fluoridation of plastic fuel tanks as one of the important measures.

Q:Where has the machine which sells the plastic processing, wants the true, begs the answer

Jiangsu and Zhejiang provinces are many (New), Heilongjiang has many families also to buy (old).

Q:My home is the county seat, want to open a waste plastic recycling, and then processed into plastic particles factory, do not know how the market? If there is cooperation between manufacturers, the best production, processing can also be.

If you don't know where your friends are, the coastal areas are the ones that sell well and the rest is not the problem. Inside the road area on the raw materials, you can not get rid of the market competition, brother did not coast?. Start doing general Kazakhstan, is to do PP, PE and other general plastic raw materials, use more widely, but profits must be low. Engineering plastics use limitations, raw materials are not so good, technical requirements are also high. Such as PC, PMMA and so on, 1-2 tons in case of no technical careless, really made waste!

Q:I found that the plastic bags and food bags used in the county town of my work are from abroad. I would like to open a plastic bag processing plant. What kind of machines do I need?. How much is it (cheaper, smaller per day)?. Where does the raw material go in?. The main market for vegetables; small bags for small food. Who will answer in detail?. Thank you

The width, thickness and color of the machine can be adjustedThe majority of raw materials is the nearest purchase, can from us into the Hebei Ningjin canal Xingtai plastic industrial zone, we will teach you the technology. We have a lot of bags around here, so you can come over and have a look.If you have time, come and visit our factoryHebei Ningjin Fuda machinery

Q:The difference between plasticization and processability of plastics in extrusion process

I. Introduction of extruderIn the screw extruder is under the action of the molten plastic extrusion through fixed shape extrusion, water cooling after cutting in the traction machine under the same section is mainly used for a variety of products. A large number of continuous production, such as tube, rod, profile, also can be used for plastic modification and granulation. The basic mechanism of extrusion is very simple a screw in the cylinder to rotate and move forward the plastic. The screw is actually a ramp or slope that is wound around the center layer. The aim is to increase the pressure to overcome the greater resistance. Is an extruder, there are 3 kinds of resistance to overcome: solid particles (feed) on the cylinder wall friction and screw rotation before laps (feed) the mutual friction between them; melt in the cylinder wall adhesion; melt pushed forward when the resistance of the internal logistics.