F-KB090 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
You Might Also Like
product name：rubber wood knife seat
material：Carbonized bamboo
N.W.：0.486kg
MEAS：14*16*8cm
Product advantage：
How does the bamboo product carbonize？Firstly，put the bamboo or bamboo bag into the high-pressure carbonized boiler of 200 degrees - 300 degrees for vapor carbonization.
And after high temperature and high pressure, so that form a hard carbide particles layer on the surface.At the same time,the bamboo itself will be more harder.
The advantage of carbonized bamboo knife seat:after carbonize,hard carbide particles will form a environment not easy living for bacteria on the surface of bamboo product to achieve the antibacterial effect.
At the same time, because after carbonization the bamboo will be more hard than ordinary paper products, preventing wearing and bamboo thorn problem.
Carbonized bamboo knife seat quantity：
Safety, health, bright color，durable，the everyday necessary good products
Anti-mildew change，anti moth
Environmental protection，no crack，no decay
- Q:How to do the slide shoe
- Re tapping, buy 8MM tap (the original nail is 6MM), buy 8mm nail, tapping the time must be vertical, that is, to ensure that the original nail in a line on the good!
- Q:However, No. 2, No. 3, the normal use of potential energy on the knife No. 4 can not be normal use of the rotation has not stopped on the 1.
- 1-2-3 knife is normal? Can't you find the knife on the number four? The 4 line may be broken or bad contact!
- Q:How can we remove the NC turret
- First remove the inside, then the following,Two screws inside, then the eye, should use a punch, turn down
- Q:Numerical control lathe tool holder does not match the system cutter number
- The turret operation is not in place (sometimes appear suddenly, the mid position stay) is mainly due to signaling disc contact and elastic sheet contact displacement, namely the cutter disc position signal to a fixed offset bakelite. At this point, it should be adjusted to the contact position of the contact plate and the elastic plate. If you still can not rule out the fault, it is possible to send the disk clamping nut loose, resulting in the location of mobile.
- Q:After the work of the machine tool, the knife is not changed, the time is good and bad, the circuit is not a problem, mechanical rotation is normal. What are the specific reasons
- Processing part of the program in the preparation of T code, the need to change the target knife number, the principle is to achieve this. The current knife number in the system inside, find the target knife number, according to the shortcut to the principle of selection, to determine the positive and negative. And calculate the number of knives that need to be turned over to the counter. In normal operation, the knife counting switch is used to subtract. The difference between the number of targets to subtraction, a reduction of 0, the completion of the signal, the library to stop running. The reason for this failure may be caused by the loose count switch and the error count. Control PLC counter in the middle, to see whether one correspondence can determine where the problem!
- Q:The difference between the turret and the rear turret NC lathe
- The classification processing example scope advantages and disadvantages of different composition of 2.3 ordinary lathe and CNC lathe CNC lathe uses a directory of the two introduction 2.1 CNC lathe 2.2 CNC lathe 2.4 CNC lathe 2.5 CNC lathe CNC lathe CNC lathe 2.6 three 3.1 NC turning process and tooling 3.2 CNC lathe programming 3.3 part four references
- Q:CNC lathe turret, sometimes why turn around.
- The general is a knife or bad coder and encoder connected to the data line broken, not to signal transmission system, data line control box is connected behind the knife and broken, suggest that you have the knife line reconnected or knife encoders change try, data line if is not the knife and the back of the control box is connected with a break
- Q:What is the difference between the KSJ and HV
- Far, the accuracy of the KSJ knife, the quality is much higher than the HV, the price in that bad! But I'm talking about genuine
- Q:What is the reason why the turret of NC lathe is not maintained?
- First, the bad disk, this may not be great.Two, the inside of the positioning pin broken.Three, the hollow shaft fracture.
- Q:Is the plastic knife holder of roller skate good or metal knife holder good?
- Each has its advantages and disadvantages, the plastic is relatively light but easy to change and no way to replace, although the metal sink, but more than a ban and can change the knife.
1. Manufacturer Overview |
|
|---|---|
| Location | |
| Year Established | |
| Annual Output Value | |
| Main Markets | |
| Company Certifications | |
2. Manufacturer Certificates |
|
|---|---|
| a) Certification Name | |
| Range | |
| Reference | |
| Validity Period | |
3. Manufacturer Capability |
|
|---|---|
| a)Trade Capacity | |
| Nearest Port | |
| Export Percentage | |
| No.of Employees in Trade Department | |
| Language Spoken: | |
| b)Factory Information | |
| Factory Size: | |
| No. of Production Lines | |
| Contract Manufacturing | |
| Product Price Range | |
Send your message to us
F-KB090 Carbonized bamboo knife seat，your best choice
- Ref Price:
-
- Loading Port:
- Guangzhou
- Payment Terms:
- TT OR LC
- Min Order Qty:
- 1000 pc
- Supply Capability:
- 100000 pc/month
OKorder Service Pledge
OKorder Financial Service
Similar products
New products
Hot products
